- 您現在的位置：買賣IC網 > PDF目錄384935 > T0P243G (Power Integrations, Inc.) Family Extended Power, Design Flexible,Integrated Off-line Switcher PDF資料下載
參數資料
| 型號： | T0P243G |
| 廠商： | Power Integrations, Inc. |
| 英文描述： | Family Extended Power, Design Flexible,Integrated Off-line Switcher |
| 中文描述： | 家庭擴展的電源，設計靈活，集成的離線切換 |
| 文件頁數： | 9/48頁 |
| 文件大?。?/td> | 771K |
| 代理商： | T0P243G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TOP242-249
9
August 8, 2000
E
7/01
DC
at higher line voltages helps prevent transformer
saturation due to large load transients in forward converter
applications. DC
of 38% at the OV threshold was chosen to
ensure that the power capability of the
TOPSwitch-GX
is not
restricted by this feature under normal operation.
Remote ON/OFF and Synchronization
TOPSwitch-GX
can be turned on or off by controlling the
current into the LINE-SENSE pin or out from the EXTERNAL
CURRENT LIMIT pin (Y or R package) and into or out from
the MULTI-FUNCTION pin (P or G package) (see Figure 11).
In addition, the LINE-SENSE pin has a 1 V threshold comparator
connected at its input. This voltage threshold can also be used
to perform remote ON/OFF control. This allows easy
implementation of remote ON/OFF control of
TOPSwitch-GX
in several different ways. A transistor or an optocoupler output
connected between the EXTERNAL CURRENT LIMIT or
LINE-SENSE pins (Y or R package) or the MULTI-FUNCTION
pin (P or G package) and the SOURCE pin implements this
function with
“
active-on
”
(Figure 22, 29 and 36) while a
transistor or an optocoupler output connected between the
LINE-SENSE pin (Y or R package) or the MULTI-FUNCTION
(P or G package) pin and the CONTROL pin implements the
function with
“
active-off
”
(Figure 23 and 37).
When a signal is received at the LINE-SENSE pin or the
EXTERNAL CURRENT LIMIT pin (Y or R package) or the
MULTI-FUNCTION pin (P or G package) to disable the output
through any of the pin functions such as OV, UV and remote
ON/OFF,
TOPSwitch-GX
always completes its current switching
cycle, as illustrated in Figure 10, before the output is forced off.
The internal oscillator is stopped slightly before the end of the
current cycle and stays there as long as the disable signal exists.
When the signal at the above pins changes state from disable to
enable, the internal oscillator starts the next switching cycle.
This approach allows the use of this pin to synchronize
TOPSwitch-GX
to any external signal with a frequency lower
than its internal switching frequency.
As seen above, the remote ON/OFF feature allows the
TOPSwitch-GX
to be turned on and off instantly, on a cycle-by-
cycle basis, with very little delay. However, remote ON/OFF
can also be used as a standby or power switch to turn off the
TOPSwitch-GX
and keep it in a very low power consumption
state for indefinitely long periods. If the
TOPSwitch-GX
is held
in remote off state for long enough time to allow the CONTROL
pin to dishcharge to the internal supply under-voltage threshold
of 4.8 V (approximately 32 ms for a 47
μ
F CONTROL pin
capacitance), the CONTROL pin goes into the hysteretic mode
of regulation. In this mode, the CONTROL pin goes through
alternate charge and discharge cycles between 4.8 V and 5.8 V
(see CONTROL pin operation section above) and runs entirely
off the high voltage DC input, but with very low power
consumption (160 mW typical at 230 VAC with M or X pins
open). When the
TOPSwitch-GX
is remotely turned on after
entering this mode, it will initiate a normal start-up sequence
with soft-start the next time the CONTROL pin reaches 5.8 V.
In the worst case, the delay from remote on to start-up can be
equal to the full discharge/charge cycle time of the CONTROL
pin, which is approximately 125 ms for a 47
μ
F CONTROL pin
capacitor. This reduced consumption remote off mode can
eliminate expensive and unreliable in-line mechanical switches.
It also allows for microprocessor controlled turn-on and turn-
off sequences that may be required in certain applications such
as inkjet and laser printers.
Soft-Start
Two on-chip soft-start functions are activated at start-up with a
duration of 10 ms (typical). Maximum duty cycle starts from
0% and linearly increases to the default maximum of 78% at the
end of the 10 ms duration and the current limit starts from about
85% and linearly increases to 100% at the end of the 10ms
duration. In addition to start-up, soft-start is also activated at
each restart attempt during auto-restart and when restarting
after being in hysteretic regulation of CONTROL pin voltage
(V
), due to remote off or thermal shutdown conditions. This
effectively minimizes current and voltage stresses on the output
MOSFET, the clamp circuit and the output rectifier during start-
up. This feature also helps minimize output overshoot and
prevents saturation of the transformer during start-up.
Shutdown/Auto-Restart
To minimize
TOPSwitch-GX
power dissipation under fault
conditions, the shutdown/auto-restart circuit turns the power
supply on and off at an auto-restart duty cycle of typically 4%
if an out of regulation condition persists. Loss of regulation
interrupts the external current into the CONTROL pin. V
C
regulation changes from shunt mode to the hysteretic auto-
restart mode as described in CONTROL pin operation section.
When the fault condition is removed, the power supply output
becomes regulated, V
regulation returns to shunt mode, and
normal operation of the power supply resumes.
Hysteretic Over-Temperature Protection
Temperature protection is provided by a precision analog
circuit that turns the output MOSFET off when the junction
temperature exceeds the thermal shutdown temperature
(140
°
C typical). When the junction temperature cools to below
the hysteretic temperature, normal operation resumes providing
automatic recovery. A large hysteresis of 70
°
C (typical) is
provided to prevent overheating of the PC board due to a
continuous fault condition. V
is regulated in hysteretic mode
and a 4.8 V to 5.8 V (typical) sawtooth waveform is present on
the CONTROL pin while in thermal shutdown.
Bandgap Reference
All critical
TOPSwitch-GX
internal voltages are derived from a
temperature-compensated bandgap reference. This reference is
相關PDF資料 |
PDF描述 |
|---|---|
| T1100 | Miniature TCXOs |
| T14L10 | Dual-In-Line, 10 Bit |
| T14L10104E3 | Dual-In-Line, 10 Bit |
| T15V8M16A | 512K X 16 LOW POWER CMOS STATIC RAM |
| T15V8M16A-100C | 512K X 16 LOW POWER CMOS STATIC RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T1 | 功能描述:TIP SOLDER 1/32"FOR PORTASOL P1C RoHS:否 類別:焊接、脫焊、返修產品 >> 尖端，噴嘴 系列:Weller®, Portasol® 標準包裝:1 系列:SFP 尖端 - 類型:焊接 尖端 - 尺寸:0.016 英寸 OD x 0.34 英寸 L（0.41mm x 8.5mm） 尖端 - 形狀:圓錐形 溫度范圍:- 適用于相關產品:SP200-21，SP200-11 配用:389-1137-ND - HANDPIECE SOLDERING CARTRIDGEMFR-2211-ND - SYSTEM SOLDER 2OUTPUT 100/240VAC |
| T-1 | 功能描述:環境檢測設備 3" Extension Bar 0.138" Shaft Diamete RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| T1 (GREEN) | 制造商:undefined 功能描述: |
| T1 3/4(GREEN) | 制造商: 功能描述: 制造商:undefined 功能描述: |
| T-1 TIP | 功能描述:烙鐵 Weller .3" Spade Tip For P1C/P1KC RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
發布緊急采購，3分鐘左右您將得到回復。