Precision Edge SY89808L Micrel, Inc. M9999-091405 hbwhelp@micrel.com or (408) 955-1690 AC ELECTRICAL " />
參數資料
型號: SY89251VMG TR
廠商: Micrel Inc
文件頁數: 4/7頁
文件大?。?/td> 0K
描述: IC RCVR ENH DIFF PECL/ECL 8-MLF
標準包裝: 1
系列: SY89
邏輯類型: 差分接收器
電源電壓: 3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-VFDFN 裸露焊盤,8-MLF?
供應商設備封裝: 8-MLF?(2x2)
包裝: 標準包裝
產品目錄頁面: 1090 (CN2011-ZH PDF)
其它名稱: 576-3500-6
4
Precision Edge
SY89808L
Micrel, Inc.
M9999-091405
hbwhelp@micrel.com or (408) 955-1690
AC ELECTRICAL CHARACTERISTICS
V
CCI = 3.3V ± 5%; VCCO = 1.8V ± 10%; All outputs are loaded with 50 to GND; TA = –40°C to +85°C, unless otherwise stated.
Symbol
Parameter
Condition
Min
Typ
Max
Units
f
MAX
Maximum Operating Frequency
V
OUT ≥ 450mV
500
——
MHz
t
pd
Propagation Delay
CLK-to-Q
Note 3
0.800
1.000
1.200
ns
SEL-to-Q
Note 3
0.800
1.200
1.700
ns
t
SKEW
Within-Device Skew
Note 4
——
25
ps
t
SKPP
Part-to-Part Skew
Note 5
——
400
ps
V
pp
Minimum Input Swing
Note 6
150
——
mV
LVPECL_CLK
V
CMR
Common Mode Range
Note 7
–1.5
—–0.4
V
LVPECL_CLK
t
S
OE Set-Up Time
Note 8
1.0
——
ns
t
H
OE Hold Time
0.5
——
ns
t
r, tf
Output Rise/Fall Time (20% – 80%)
250
450
650
ps
t
JITTER
Cycle-to-Cycle Jitter
Note 9
1ps
RMS
Total Jitter
Note 10
10
ps
PP
3. Differential propagation delay is defined as the delay from the crossing point of the differential input signals to the crossing point of the differential
output signals.
4. The within-device skew is defined as the worst case difference between any two similar delay paths within a single device operating at the
same voltage and temperature.
5. The part-to-part skew is defined as the absolute worst case difference between any two delay paths on any two devices operating at the same
voltage and temperature.
6. The V
PP (min.) is defined as the minimum input differential voltage which will cause no increase in the propagation delay.
7. V
CMR is defined as the range within which the VIH level may vary, with the device still meeting the propagation delay specification. The
numbers in the table are referenced to VCCI. The VIL level must be such that the peak-to-peak voltage is less than 1.0V and greater than or
equal to V
PP (min.). The lower end of the CMR range varies 1:1 with VCCI. The VCMR (min) will be fixed at 3.3V – |VCMR (min)|.
8. OE set-up time is defined with respect to the rising edge of the clock. OE HIGH to LOW transition ensures outputs remain disabled during the
next clock cycle. OE LOW to HIGH transition enables normal operation of the next input clock.
9. Cycle-to-cycle jitter definition: the variation of periods between adjacent cycles, T
n–Tn–1 where T is the time between rising edges of the
output signal.
10. Total jitter definition: with an ideal clock source of
≤ f
max, no more than one output edge in 10
12 output edges will deviate by more than the
specified amount.
相關PDF資料
PDF描述
SY89307VMI TR IC RECEIVER DIFF 3.3V/5V 8-MLF
SY89311UMI TR IC CLK FANOUT BUFF 1:2 3GHZ 8MLF
SY89312VMI TR IC CLOCK GEN /2 3.3V/5V 8-MLF
SY89313VMI TR IC CLOCK GEN /4 3.3V/5V 8-MLF
SY89316VMI TR IC RCVR/BUFF 3.3V/5V 2.5GHZ 8MLF
相關代理商/技術參數
參數描述
SY89295U 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2.5V/3.3V 1.5GHz Precision LVPECL
SY89295U_06 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2.5V/3.3V 1.5GHz PRECISION LVPECL PROGRAMMABLE DELAY
SY89295U_11 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2.5V/3.3V 1.5GHz Precision LVPECL
SY89295U-EVAL 制造商:Micrel Inc 功能描述:2.5V/3.3V PECL DELAY LINE - EV
SY89295UMG 功能描述:延遲線/計時元素 2.5V/3.3V PECL Delay Line (I Temp, Green) RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube