參數資料
型號: SY01-S3T
廠商: Raltron Electronics Corporation
英文描述: SYNCHRONOUS EQUIPMENT TCXO BASED STRATUM 3 CLOCK UNIT
中文描述: 基于同步設備溫補地層3時鐘單元
文件頁數: 4/7頁
文件大小: 182K
代理商: SY01-S3T
SYNCHRONOUS EQUIPMENT
TCXO BASED STRATUM 3 CLOCK UNIT – SY01-S3T
the clock is mounted. The SY01-S3T uses an TCXO as an on-board oscillator but other types of oscillators are
available.
Locked to Ref.1
In this mode the output of the module is phase locked to input reference 1.
Locked to Ref.2
In this mode the output of the module is phase locked to input reference 2.
The REF1 or REF2 Modes are typically used when a slave clock source is synchronized to the network. In these
modes, the SY01-S3T provides timing signals, which are synchronized, to one of two references inputs (REF1 or
REF2). The input reference signals may have a variety of nominal frequencies, which is typically specified by the end
user. When the modes are selected the unit goes through a reference evaluation, and then a frequency acquisition,
and finally to phase locking.
Input References
The SY01-S3T module accepts two input references EX REF1 and EX REF2. End users can specify the frequencies
within a range of 8 kHz to 77.76 MHz. The input reference signals are HCMOS/TTL levels with timing characteristic in
according to Bellcore GR-1244-core 3.2.1.R3-1 or equivalent standards. Please note that the end user must specify
the two input frequencies at the time of order.
Output Signals
The SY01-S3T module provides two output signals OUT and OPT OUT. The outputs are generated by the internal
oscillator and scaled by the output frequency converters. The performance of the module significantly depends on the
internal oscillator and special care was taken to define its specification. A Oven Controlled Crystal Oscillator (TCXO) is
used as the internal oscillator. The frequency of the oscillator is specified according to the network application where
the SY01-S3T will be used. The frequency converters divide signal from the oscillator to the specified frequencies.
The SY01 Operation mode
By changing the control inputs the user can change the state of the SY01 according to the state diagram. The
SY01 offers two ways to manage state machine:
J1 jumper
Open
Closed
The behavior of the Manual and Automatic controls are shown on the figures 2 and 3 with an explanation for each
transition. In the Automatic control the SY01 can be automatically switched to the reference (if available)
regardless of status of the control inputs. In Manual control the unit waits for control inputs to be changed. In both
modes the unit will go to the REFERENCE EVALUATION if the previously lost reference is required.
Control
Two controls are available for the user to control the operation of the SY01. The two external inputs CNT1 and CNT2
provide this feature. Below, the truth table shows behavior of the SY01 module according to the control inputs states.
CNT2
CNT1
MODE OF OPERATION
RALTRON ELECTRONICS CORP.
§
10651 N.W.19
th
St
§
Florida 33172
§
U.S.A.
Tel: 305 593-6033
§
Fax: 305-594-3973
§
e-mail: sales@raltron.com
§
Internet: http:/www.raltron.com
State diagram control
Manual
Automatic
相關PDF資料
PDF描述
SY01-S3 SYNCHRONOUS EQUIPMENT OCXO BASED STRATUM 3 CLOCK UNIT
SY01-SMC SYNCHRONOUS EQUIPMENT SONET MINIMUM CLOCK
SY02-FEC SYNCHRONOUS EQUIPMENT HIGH FREQUENCY CLOCK REGENERATOR
SY02-HIPL SYNCHRONOUS EQUIPMENT HIGH IN/OUTPUT FREQUENCY CLOCK/SYNCHRONIZER
SY02-HLPL SYNCHRONOUS EQUIPMENT HIGH FREQUENCY HITLESS SYNCHRONIZER
相關代理商/技術參數
參數描述
SY01-SMC 制造商:RALTRON 制造商全稱:RALTRON 功能描述:SYNCHRONOUS EQUIPMENT SONET MINIMUM CLOCK
SY0206-R 制造商:JAMECO VALUEPRO 功能描述:CASE,METAL,6.3 INCH X7.75 INCH X2.5 INCH ,
SY0207-R 制造商:JAMECO VALUEPRO 功能描述:CASE,METAL,7.5 INCH X9.8 INCH X3.2 INCH ,
SY025M0047B2F-0511 制造商:Yageo Corporation 功能描述:
SY025M0100BZF-0611 制造商:Yageo Corporation 功能描述: