參數資料
| 型號： | SX8723CWLTDT |
| 廠商： | Semtech |
| 文件頁數： | 14/67頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS ADC 16BIT I2C/SRL |
| 標準包裝： | 1 |
| 系列： | ZoomingADC™ |
| 類型： | 數據采集系統(tǒng)（DAS） |
| 輸入類型： | 差分 |
| 輸出類型： | 數字 |
| 接口： | I²C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 12-MLPD-EP（4x4） |
| 包裝： | 標準包裝 |
| 其它名稱： | SX8723CWLTDTDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
www.semtech.com/products/
Page 21
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
SX8723C
ZoomingADC for sensing data acquisition
Revision 1.01
January 2011
Semtech
(3)
SetNelconv: (rw) sets the number of elementary conversions to 2
(SetNelconv[1:0]). To compensate for offsets, the input signal is chopped
between elementary conversions (1,2,4,8).
(4)
SetOsr: (rw) sets the over-sampling rate (OSR) of an elementary conversion to 2
(3+SetOsr[2:0]). OSR = 8, 16, 32, ..., 512, 1024.
(5)
Continuous: (rw) setting this bit starts a conversion. When this bis is 1, A new conversion will automatically begin directly when the previ-
ous one is finished.
(6)
Reserved
(7)
IbAmpAdc: (rw) sets the bias current in the ADC to 0.25 x (1+ IbAmpAdc[1:0]) of the normal operation current (25, 50, 75 or 100% of nom-
inal current). To be used for low-power, low-speed operation.
(8)
IbAmpPga: (rw) sets the bias current in the PGAs to 0.25 x (1+IbAmpPga[1:0]) of the normal operation current (25, 50, 75 or 100% of nom-
inal current). To be used for low-power, low-speed operation.
(9)
Enable: (rw) enables the ADC modulator (bit 0) and the different stages of the PGAs (PGAi by bit i=1,2,3). PGA stages that are disabled are
bypassed.
(10)
SetFs: (rw) These bits set the over sampling frequency of the acquisition chain. Expressed as a fraction of the oscillator frequency, the
sampling frequency is given as: 11 ' 500 kHz, 10 ' 250 kHz, 01 ' 125 kHz, 00 ' 62.5 kHz.
(11)
Pga1Gain: (rw) sets the gain of the first stage: 0 ' 1, 1 ' 10.
(12)
Pga2Gain: (rw) sets the gain of the second stage: 00 ' 1, 01 ' 2, 10 ' 5, 11 ' 10.
(13)
Pga3Gain: (rw) sets the gain of the third stage to Pga3Gain[6:0] 1/12.
(14)
Pga2Offset: (rw) sets the offset of the second stage between -1 and +1, with increments of 0.2. The MSB gives the sign (0 positive, 1 neg-
ative); amplitude is coded with the bits Pga2Offset[5:0].
(15)
Pga3Offset: (rw) sets the offset of the third stage between -5.25 and +5.25, with increments of 1/12. The MSB gives the sign (0 positive, 1
negative); amplitude is coded with the bits Pga3Offset[5:0].
(16)
Busy: (r) set to 1 if a conversion is running.
(17)
Def: (w) sets all values to their defaults (PGA disabled, max speed, nominal modulator bias current, 2 elementary conversions, over-sam-
pling rate of 32) and starts a new conversion without waiting the end of the preceding one.
(18)
Amux(4:0): (rw) Amux[4] sets the mode (0 ' differential inputs, 1 ' single ended inputs with A0= common reference) Amux[3] sets the sign
(0 ' straight, 1' cross) Amux[2:0] sets the channel.
(19)
Vmux: (rw) sets the differential reference channel (0 ' VBATT, 1 ' VREF).
7.3 Input Multiplexers (AMUX and VMUX)
The ZoomingADC has analog inputs AC0 to AC5 and reference inputs. Let us first define the differential input voltage
VIN and reference voltage VREF,ADC respectively as:
As shown in Table 9, the inputs can be configured in two ways: either as 4 differential channels (VIN1= AC1 - AC0,... , VIN3
= AC5 - AC4), or AC0 can be used as a common reference, providing 7 signal paths all referred to AC0. The control word
for the analog input selection is Amux. Notice that the Amux bit 4 controls the sign of the input voltage.
Equation 3
Equation 4
Table 9. Analog Input Selection
Amux
(RegACCfg5[5:1])
VINP
VINN
Amux
(RegACCfg5[5:1])
VINP
VINN
Sign S = 1
Sign S = -1
00x00
AC1(VREF)AC0(VSS)
01x00
AC1(VSS)AC0(VREF)
]
[V
V
INN
INP
IN
=
]
[V
V
REFN
REFP
REF
=
Not
Recommended
for
New
Designs
相關PDF資料 |
PDF描述 |
|---|---|
| SX8723E083TDT | IC DAS PRESS/TEMP SENS 12MLPD |
| SX8724CWLTDT | IC DAS ADC 16BIT I2C/SRL |
| SX8724E082TDT | IC DAS PRESS/TEMP SENS 16MLPQ |
| SX8725CWLTDT | IC DAS ADC 16BIT I2C/SRL |
| SX8725E083TDT | IC DAS PRESS/TEMP SENS 12MLPD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SX8723E083TDT | 功能描述:IC DAS PRESS/TEMP SENS 12MLPD RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:ZoomingADC™ 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| SX8723E083TRT | 功能描述:IC DAS PRESSURE/TEMP SENS 12MLPD RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:ZoomingADC™ 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| SX8723S | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:ZoomingADC for sensing data acquisition |
| SX8723SWLTDT | 制造商:Semtech Corporation 功能描述:2 INPUTS ZOOMING ADC WITH SPI |
| SX8724 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:ZoomingADC? for Pressure and Temperature Sensing |
發(fā)布緊急采購，3分鐘左右您將得到回復。