- 您現在的位置：買賣IC網 > PDF目錄383849 > SWPTC-01 SWPTC-01 Programming Software for PTC-01 Programmer PDF資料下載
參數資料
| 型號： | SWPTC-01 |
| 英文描述： | SWPTC-01 Programming Software for PTC-01 Programmer |
| 中文描述： | SWPTC - 01 PTC軟件編程，01編程 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 914K |
| 代理商： | SWPTC-01 |
PTC-01
Software for MLX90215
PTC-01 Programmer User’s Manual Rev 1.2 15/NOV/2001 Page 17
Opening/Creating a Log File
The first step in setting up the data log is to open a log file. To create a new log file choose open from log
file menu. Type in the file name and click save. To append an existing log file select “append” from the log
menu. Choose the log file and click save.
Configuring the Data Log Parameters
After a log file has been opened the user must configure the log parameters. The parameters are located
under the Log preferences window. To access the Log preferences window the user can select
“preferences” from the log menu. The log preferences menu is displayed below.
The preferences window is divided into two tabs, Manual Mode and Auto Mode. The tabs correspond to the
manual and auto-calibration interfaces. The log function for each interface is independent. Therefore the log
parameters must be configured separately. By clicking on the tabs the user can switch between the two con-
figurations. Displayed above is the Auto Mode tab for configuration of the auto-calibration data log.
Listed in the log preferences window are two list, Available and Selected. The items listed under available
represent the parameters that may be recorded in the log file. The selected items represent the parameters
that will be recorded. The user can use the buttons between the two columns to add and remove items. The
items in the selected will be recorded in the same order as shown in list. Using the “Move Up” and “Move
Down” button the user can change the order of the parameters.
At the bottom of the Auto Mode tab is the option for the software to automatically log the selected parameters.
The users has three options, Manual Only, After Calibration, and After Zap. The Manual Only option will only
log parameters when the user executes the log functions. The After Calibration option will log parameters
after the user has executed the calibration function. Similarly, the After Zap option will log parameters after
the user executes the zap function.
The automatic logging options are not available in Manual Mode. When in the manual calibration interface
parameters will only be recorded when the user executes the log function.
When finished with the log preferences click ok to close the window. The log preferences will be saved
when the devices session is saved.
相關PDF資料 |
PDF描述 |
|---|---|
| SWR200CF | Waveform Generator/Support |
| SWR200MF | Waveform Generator/Support |
| SWR300CD | Analog IC |
| SWR300CS | Analog IC |
| SWR300LD | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SWPTHROCKERDPST | 制造商:Schaffner 功能描述:SWITCHES AND VOLTAGE SELECTORS |
| SWP-TX-1 UNICOM | 制造商:FLORIDA MISC. 功能描述: 制造商:Florida Misc. 功能描述: |
| SWP-TX-2 UNICOM | 制造商:FLORIDA MISC. 功能描述: 制造商:Florida Misc. 功能描述: |
| SWPZ-A041GG-M025 | 制造商:JST Manufacturing 功能描述:WPZ Serie Female Terminal |
| SWQ327-30.720 | 制造商:SUNTSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。