- 您現在的位置：買賣IC網 > PDF目錄382566 > STR712FR2T6 (意法半導體) ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES PDF資料下載
參數資料
| 型號： | STR712FR2T6 |
| 廠商： | 意法半導體 |
| 英文描述： | ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES |
| 中文描述： | ARM7TDMI的？ 16/32位微控制器5定時器，ADC和10 COMMUNICAT離子接口與閃存，USB，可以 |
| 文件頁數： | 17/49頁 |
| 文件大?。?/td> | 678K |
| 代理商： | STR712FR2T6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
STR71xF - INTRODUCTION
17/49
1. The Reset configuration of the I/O Ports is IPUPD (input pull-up/pull down). Refer to
Table 7, “Port Bit Configuration Table,” on page 26
. The Port bit configuration at reset is
PC0=1, PC1=1, PC2=0. The port data register bit (PD) value depends on the pu/pd column
which specifies whether the pull-up or pull-down is enabled at reset
2. In reset state, these pins configured as Input PU/PD with weak pull-up enabled. They must
be configured by software as Alternate Function (see
Table 7, “Port Bit Configuration Table,”
on page 26
) to be used by the External Memory Interface.
3. In reset state, these pins configured as Input PU/PD with weak pull-down enabled to output
Address 0x0000 0000 using the External Memory Interface. To access memory banks greater
than 1Mbyte, they need to be configured by software as Alternate Function (see
Table 7, “Port
Bit Configuration Table,” on page 26
).
136 B5
WE.1
O
8mA
External Memory Interface: active low MSB write ena-
ble output
External Memory Interface: active low LSB write enable
output
Supply voltage for digital I/Os
Ground voltage for digital I/Os
Port 0.5
SPI1: Master out/Slave In data
Port 0.6
SPI1: Serial Clock
Port 0.7
SPI1: Slave Select input active low
UART0: Receive
Data input
Note:
This pin may be used for single wire UART (half
duplex) if programmed as Alternate Function Output.
The pin will be tri-stated except when UART transmis-
sion is in progress
Select Boot Con-
figuration input
137 C5
WE.0
O
8mA
138 A3
139 A2
140 D5
141 A4
142 B4
V
33
V
SS
P0.5/S1.MOSI
P0.6/S1.SCLK
P0.7/S1.SS
S
S
I/O pu
I/O pu
I/O pu
C
T
C
T
C
T
4mA X
X 4mA X
4mA X
X
X
X
143 C4
P0.8/U0.RX/
U0.TX
I/O pd C
T
X 4mA T
Port 0.8
UART0: Transmit data
output.
144 B3
P0.9/U0.TX/
BOOT.0
I/O pd C
T
4mA X
X
Port 0.9
UART0: Transmit data
output
Table 3. STR710 Pin Description
Pin n°
Pin Name
T
I
1
Input
Output
A
Main
function
(after
reset)
Alternate function
T
B
i
C
O
P
相關PDF資料 |
PDF描述 |
|---|---|
| STR710FZ2T6 | ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES |
| STR711FR1T6 | ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES |
| STR711FR2T6 | ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES |
| STR71XF | ARM7TDMI? 16/32-BIT MCU WITH FLASH, USB, CAN 5 TIMERS, ADC, 10 COMMUNICATIONS INTERFACES |
| STS10PF30L | P-CHANNEL 30V - 0.012Ohm - 10A SO-8 STripFET II POWER MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STR712FR2XX | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:ARM7TDMI⑩ 32-bit MCU with Flash, USB, CAN 5 timers, ADC, 10 communications interfaces |
| STR712-SK | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:IAR’s complete, low cost starter kits for STR7 and STR9 |
| STR712-SK/IAR | 功能描述:開發板和工具包 - ARM Starter Kit for STR712 Series RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| STR712-SKIAR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:IAR’s complete, low cost starter kits for STR7 and STR9 |
| STR715FR0 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:ARM7TDMI⑩ 32-bit MCU with Flash, USB, CAN 5 timers, ADC, 10 communications interfaces |
發布緊急采購，3分鐘左右您將得到回復。