參數資料
型號： ST72652R4T1
英文描述： ST7 - LOW-POWER. FULL-SPEED USB 8-BIT MCU WITH 32K FLASH. 5K RAM. FLASH CARD I/F. TIMER. PWM. ADC. I2C
中文描述： ST7的-低功耗。全速USB 8位32K快閃微控制器。 5K內存。閃存卡的I /樓計時器。脈寬調制。 ADC的。的I2C
文件頁數： 67/166頁
文件大小： 2089K
代理商： ST72652R4T1
ST7265x
159/166
15 DEVICE CONFIGURATION AND ORDERING INFORMATION
Each device is available for production in user pro-
grammable versions (FLASH) as well as in factory
coded versions (ROM). FLASH devices are
shipped to customers with a default content (FFh),
while ROM factory coded parts contain the code
supplied by the customer. This implies that FLASH
devices have to be configured by the customer us-
ing the Option Bytes while the ROM devices are
factory-configured.
15.1 OPTION BYTE
The option byte allows the hardware configuration
of the microcontroller to be selected.
The option byte has no address in the memory
map and can be accessed only in programming
mode (for example using a standard ST7 program-
ming tool). The default content of the FLASH is
fixed to FFh. This means that all the options have
“1” as their default value.
In masked ROM devices, the option byte is fixed in
hardware by the ROM code (see option list)
OPT7 = Reserved. Must be kept at 1.
OPT6 = PE5PU
I/O Port PE5 Pull-up Option
This option bit determines if a pull-up is connected
on Port E5.
0: Pull up present on PE5
1: No pull-up on PE5
When PE5PU=00:
– For input, software can enable or disable the
pull-up by programming PEOR.5 and PED-
DR.5=0.
– For output, the pull-up is enabled when Open
Drain is selected by programming PEOR.5= and
PEDDR.5=1.
Refer to the following table.
OPT5:4 = PSMOD[1:0]
Power Supply Mode
These option bits configure the power supply
mode.
OPT3 = Reserved. Must be kept at 1.
OPT2= WDG SW
Hardware or software watchdog
This option bit selects the watchdog type.
0: Hardware (watchdog always enabled)
1: Software (watchdog to be enabled by software)
OPT1 = USBEN
0: USBEN alternate function disabled. Port F4 is
free for general purpose I/O
1: USBEN alternate function enabled on Port F4
(function controlled by hardware)
OPT0= FMP_R
Flash memory read-out protection
This option indicates if the user flash memory is
protected against read-out piracy. This protection
is based on read and a write protection of the
memory in test modes and IAP. Erasing the option
bytes when the FMP_R option is selected will
cause the whole user memory to be erased first,
and the device can be reprogrammed. Refer to the
ST7 Flash Programming Reference Manual and
section 4.4 on page 22 for more details.
0: Read-out protection enabled
1: Read-out protection disabled
70
-
PE5
PU
PS
MOD
1
PS
MOD
0
-
WDG
SW
USB
EN
FMP_
R
Configuration
PE5PU
OPTION
PEOR.5
PEDDR.5
Input floating
0
00
Output Open Drain
with Pull-up
01
Input with pull-up
1
0
Output push pull
1
Input floating
1
00
Output Open Drain
0
1
Input floating
1
0
Output push pull
1
Mode
OPT5
OPT4
Stand-alone mode forced
0
Dual Supply (normal) Mode
x
1
USB mode forced
1
0
相關PDF資料
PDF描述
ST7271J1B1 8-BIT MICROCONTROLLER
ST7271N1B1 8-BIT MICROCONTROLLER
ST7271N2 Microcontroller
ST7271N3B1 8-BIT MICROCONTROLLER
ST7271N5B1 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
ST7265X-EVAL/MS 制造商:STMicroelectronics 功能描述:ST6 EVAL BD - Bulk
ST7265X-EVAL/PFD 制造商:STMicroelectronics 功能描述:USB FLASH EVAL - Bulk
ST7266 制造商:6940 功能描述:ST7266
ST7267C8T1L 制造商:STMicroelectronics 功能描述:
ST72681/R12 制造商:STMicroelectronics 功能描述:CONTROLLER FOR HIGH-PERFORMANCE BUS-POWERED USB 2.0 FLASH DR - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*