參數資料
型號: ST52F513Y1B6
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16
封裝: PLASTIC, DIP-16
文件頁數: 34/106頁
文件大?。?/td> 648K
代理商: ST52F513Y1B6
ST52F510/F513/F514
33/106
A similar procedure can be used to write a single
block:
1.
The
SetPage command is sent, followed by
the page number where the data should be
written
2.
The
IncBlock command is sent as many times
as the block number inside the page (for ex-
ample: to address the block 3 the
IncBlock
must be sent 3 times)
3.
The
WriteBlock command is sent followed by
the 32 data bytes to be written.
4.
After the 32th byte is sent, the device holds
the SCL line low until all the data are not
stored in the memory (about 4.5 ms: 2 ms for
erasing and 2.5 for writing: the same time for
a single byte)
The procedures described previously can be
repeated as many time as needed, without exiting
from Programming Mode or re-sending the Slave
Address again.
The commands ByteErase and BlockErase, used
instead of ByteWrite and BlockWrite, erase (put all
bit to 0) the specified memory location or block.
4.2.4 Option Bytes Programming. The
Option
Byte addresses cannot be accessed with a
sequential procedure like the one described in
Section
4.2.2.
Actually,
the
pointers
are
automatically incremented up to the last block or
address in page 31. A further increment sets all the
pointers to 0.
The Option Byte addresses (located at page 48,
block 0, addresses 0-7) must be accessed with a
direct addressing procedure as the one described
in Section 4.2.3.
If the Fast Programming procedure is used, it must
be followed by a Random Block Writing procedure
to program the Option Bytes. The other 24 bytes of
the block can be written with dummy values.
Figure 4.2 Programming Procedures
Fast Programming Procedure
Random Byte Writing Procedure
Random Block Writing Procedure
Option Byte Writing Procedure
S=Start, P=Stop, A=Acknowledge, NA=Non-acknowledge
From Slave to Master
From Master to Slave
S 10100000
A
00000000
A
GlobalErase
A
FastBlockWrite
A
Data0
A
.... .
.....
Data31
A
IncBlock
A
FastBlockWrite
A
.....
Data31
A
.....
Data31
A
P
.....
SetPage
A
Page Address
A
ByteWrite
A
Byte Address
A
Data
A
Command
.....
SetPage
A
Page Address
A
IncBlock
A
.....
IncBlock
A
BlockWrite
A
Data0
A
.....
Data31
A
Command
.....
SetPage
A
00110000
A
WriteBlock
A
Option Byte 0
A
..... Option Byte 7
A
.....
Dummy 0
A
.....
Dummy 23
A
P
相關PDF資料
PDF描述
ST52F513Y2B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16
ST52F510Y3B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16
ST52F514Y2B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16
ST52T430K3B6 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDIP32
ST52T430K3T6 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
ST52F513Y3M6 制造商:STMicroelectronics 功能描述:
ST52F513YMM6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI
ST52F514 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI
ST52F514F0B6 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
ST52F514F0M6 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller