- 您現在的位置：買賣IC網 > PDF目錄384931 > ST16C552IJ68 (STARTECH SEMICONDUCTOR INC) DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT PDF資料下載
參數資料
| 型號： | ST16C552IJ68 |
| 廠商： | STARTECH SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| 中文描述： | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| 文件頁數： | 19/39頁 |
| 文件大?。?/td> | 222K |
| 代理商： | ST16C552IJ68 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
19
ST16C552/552A
Rev. 3.40
IER BIT 6-7:
Not Used - initialized to a logic 0.
FIFO Control Register (FCR)
This register is used to enable the FIFO’s, clear the
FIFO’s, set the receive FIFO trigger levels, and select
the DMA mode. The DMA, and FIFO modes are
defined as follows:
DMA MODE
Mode 0
single transmit or receive operation, and is similar to
the ST16C450 mode. Transmit Ready (-TXRDY) will
go to a logic 0 when ever an empty transmit space is
available in the Transmit Holding Register (THR).
Receive Ready (-RXRDY) will go to a logic 0 when-
ever the Receive Holding Register (RHR) is loaded
with a character.
Mode 1
Set and enable the interrupt in a block
mode operation. The transmit interrupt is set when the
transmit FIFO is below the programmed trigger level.
-TXRDY remains a logic 0 as long as one empty FIFO
location is available. The receive interrupt is set when
the receive FIFO fills to the programmed trigger level.
However the FIFO continues to fill regardless of the
programmed level until the FIFO is full. -RXRDY
remains a logic 0 as long as the FIFO fill level is above
the programmed trigger level.
Set and enable the interrupt for each
FCR BIT-0:
Logic 0 = Disable the transmit and receive FIFO.
(normal default condition)
Logic 1 = Enable the transmit and receive FIFO. This
bit must be a “1” when other FCR bits are written to or
they will not be programmed.
FCR BIT-1:
Logic 0 = No FIFO receive reset. (normal default
condition)
Logic 1 = Clears the contents of the receive FIFO and
resets the FIFO counter logic (the receive shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-2:
Logic 0 = No FIFO transmit reset. (normal default
condition)
Logic 1 = Clears the contents of the transmit FIFO and
resets the FIFO counter logic (the transmit shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-3:
Logic 0 = Set DMA mode “0”. (normal default condi-
tion)
Logic 1 = Set DMA mode “1.”
Transmit operation in mode “0”:
When the 552/552A is in the ST16C450 mode (FIFO’s
disabled, FCR bit-0 = logic 0) or in the FIFO mode
(FIFO’s enabled, FCR bit-0 = logic 1, FCR bit-3 = logic
0) and when there are no characters in the transmit
FIFO or transmit holding register, the -TXRDY pin will
be a logic 0. Once active the -TXRDY pin will go to a
logic 1 after the first character is loaded into the
transmit holding register.
Receive operation in mode “0”:
When the 552/552A is in mode “0” (FCR bit-0 = logic
0) or in the FIFO mode (FCR bit-0 = logic 1, FCR bit-
3 = logic 0) and there is at least one character in the
receive FIFO, the -RXRDY pin will be a logic 0. Once
active the -RXRDY pin will go to a logic 1 when there
are no more characters in the receiver.
Transmit operation in mode “1”:
When the 552/552A is in FIFO mode ( FCR bit-0 =
logic 1, FCR bit-3 = logic 1 ), the -TXRDY pin will be
a logic 1 when the transmit FIFO is completely full. It
will be a logic 0 if one or more FIFO locations are
empty.
Receive operation in mode “1”:
When the 552/552A is in FIFO mode (FCR bit-0 = logic
1, FCR bit-3 = logic 1) and the trigger level has been
reached, or a Receive Time Out has occurred, the -
RXRDY pin will go to a logic 0. Once activated, it will
go to a logic 1 after there are no more characters in the
FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C552CJ68 | Voltage Regulator IC; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:2.5V; Supply Voltage Max:6V; Current Rating:350mA; Leaded Process Compatible:No; Output Current Max:350mA; Output Voltage Max:2.5V RoHS Compliant: No |
| ST16C552ACJ68 | DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| ST16C650A | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACJ44 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACP40 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C552IJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552IJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C554 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO |
| ST16C554CJ-0A-EVB | 功能描述:界面開發工具 Supports C554D 68 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C554CQ-0A-EVB | 功能描述:界面開發工具 Supports C554 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。