- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C552 (Exar Corporation) Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) PDF資料下載
參數資料
| 型號： | ST16C552 |
| 廠商： | Exar Corporation |
| 英文描述： | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| 中文描述： | 雙UART），16字節FIFO和并行打印機端口（雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口） |
| 文件頁數： | 22/40頁 |
| 文件大小： | 463K |
| 代理商： | ST16C552 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
22
ST16C552/552A
Rev. 3.30
LCR
Bit-5
LCR
Bit-4
LCR
Bit-3
Parity selection
X
0
0
1
1
X
0
1
0
1
0
1
1
1
1
No parity
Odd parity
Even parity
Force parity odd parity
Forced even parity
LCR BIT-6:
When enabled the Break control bit causes a break
condition to be transmitted (the TX output is forced to
a logic 0 state). This condition exists until disabled by
setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (normal default
condition)
Logic 1 = Forces the transmitter output (TX) to a logic
0 for alerting the remote receiver to a line break
condition.
LCR BIT-7:
The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled. (normal default
condition)
Logic 1 = Divisor latch and enhanced feature register
enabled.
Modem Control Register (MCR)
This register controls the interface with the modem or
a peripheral device.
MCR BIT-0:
Logic 0 = Force -DTR output to a logic 1. (normal
default condition)
Logic 1 = Force -DTR output to a logic 0.
MCR BIT-1:
Logic 0 = Force -RTS output to a logic 1. (normal
default condition)
Logic 1 = Force -RTS output to a logic 0.
MCR BIT-2:
This bit is used in the Loop-back mode only. In the
loop-back mode this bit is use to write the state of the
modem -RI interface signal.
MCR BIT-3: (
Used to control the modem -CD signal
in the loop-back mode.)
Logic 0 = Forces INT (A-B) outputs to the three state
mode. (normal default condition) In the Loop-back
mode, sets -CD internally to a logic 1.
Logic 1 = Forces the INT (A-B) outputs to the active
mode. In the Loop-back mode, sets -CD internally to
a logic 0.
MCR BIT-4:
Logic 0 = Disable loop-back mode. (normal default
condition)
Logic 1 = Enable local loop-back mode (diagnostics).
MCR BIT 5-6:
Not Used - initialized to a logic 0.
MCR BIT-7:
Logic 0 = Disable power down mode. (normal, default
condition, 552 only)
Logic 1 = Enable power down mode (IER bit-5 must
also be a logic 1 before power down will be activated).
Line Status Register (LSR)
This register provides the status of data transfers
between. the 552/552A and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register or FIFO.
(normal default condition)
Logic 1 = Data has been received and is saved in the
receive holding register or FIFO.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred
in the receive shift register. This happens when addi-
tional data arrives while the FIFO is full. In this case
the previous data in the shift register is overwritten.
Note that under this condition the data byte in the
receive shift register is not transferred into the FIFO,
therefore the data in the FIFO is not corrupted by the
error.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
| ST68C554 | QUAD UART WITH 16-BYTE FIFOS |
| ST16C554DIJ68 | Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes |
| ST16C554DIQ64 | QUAD UART WITH 16-BYTE FIFOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C552ACJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C552ACJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552ACJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552AIJ68 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| ST16C552AIJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。