- 您現在的位置：買賣IC網 > PDF目錄384931 > ST16C454 (Exar Corporation) QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) PDF資料下載
參數資料
| 型號： | ST16C454 |
| 廠商： | Exar Corporation |
| 英文描述： | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| 中文描述： | 四通用異步接收/發送器（UART） |
| 文件頁數： | 6/30頁 |
| 文件大小： | 378K |
| 代理商： | ST16C454 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ST16C454/68C454
6
Rev. 3.20
under R/-W.
-IRQ
15
O
Interrupt Request or Interrupt A - This function is associated with
the 68 mode only. In the 68 mode, interrupts from UART channels
A-D are WIRE-ORed internally to function as a single IRQ
interrupt. This pin transitions to a logic 0 (if enabled by the interrupt
enable register) whenever a UART channel(s) requires service.
Individual channel interrupt status can be determined by address-
ing each channel through its associated internal register, using -
CS and A3-A4. In the 68 mode an external pull-up resistor must be
connected between this pin and VCC. The function of this pin
changes to INTA when operating in the 16 mode, see definition
under INTA.
-RESET
RESET
37
I
Reset. - In the 16 mode a logic 1 on this pin will reset the internal
registers and all the outputs. The UART transmitter output and the
receiver input will be disabled during reset time. (See ST16C454
External Reset Conditions for initialization details.) When 16/-68
is a logic 0 (68 mode), this pin functions similarly but, as an inverted
reset interface signal, -RESET.
R/-W
18
I
Read/Write Strobe (active low) - This function is associated with
the 68 mode only. This pin provides the combined functions for
Read or Write strobes. A logic 1 to 0 transition transfers the
contents of the CPU data bus (D0-D7) to the register selected by
-CS and A0-A4. Similarly a logic 0 to 1 transition places the
contents of a 454 register selected by -CS and A0-A4 on the data
bus, D0-D7, for transfer to an external CPU.
VCC
VCC
13
47,64
I
Power supply inputs.
XTAL1
35
I
Crystal or External Clock Input - Functions as a crystal input or as
an external clock input. A crystal can be connected between this
pin and XTAL2 to form an internal oscillator circuit (see figure 8).
Alternatively, an external clock can be connected to this pin to
provide custom data rates (see Baud Rate Generator Program-
ming).
XTAL2
36
O
Output of the Crystal Oscillator or Buffered Clock - (See also
XTAL1). Crystal oscillator output or buffered clock output.
Symbol
Pin
Signal
type
Pin Description
SYMBOL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C454CJ68 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454IJ68 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST68C454 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C550CQ48 | UART WITH 16-BYTE FIFO’s |
| ST16C550IJ44 | UART WITH 16-BYTE FIFO’s |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C454_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454CJ | 制造商:Exar Corporation 功能描述: |
| ST16C454CJ-0A-EVB | 功能描述:界面開發工具 Supports C454 68 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C454CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C454CJ68-F | 功能描述:UART 接口集成電路 QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。