- 您現在的位置：買賣IC網 > PDF目錄1969 > ST16C450CP40-F (Exar Corporation)IC INTERFACE UART PDF資料下載
參數資料
| 型號： | ST16C450CP40-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 23/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE UART |
| 標準包裝： | 9 |
| 系列： | * |
| 其它名稱： | 1016-1760 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
ST16C450
4
Rev. 4.20
Symbol
Pin
Signal
Pin Description
40
44
48
type
A0
28
31
28
I
Address-0 Select Bit Internal registers address selection.
A1
27
30
27
I
Address-1 Select Bit Internal registers address selection.
A2
26
29
26
I
Address-2 Select Bit Internal registers address selection.
IOR
22
25
20
I
Read data strobe. Its function is the same as -IOR (see -
IOR), except it is active high. Either an active -IOR or IOR
is required to transfer data from 16C450 to CPU during a
read operation.
CS0
12
14
9
I
Chip Select-0. Logical 1 on this pin provides the chip select-
0 function.
CS1
13
15
10
I
Chip Select-1. Logical 1 on this pin provides the chip select-
1 function.
-CS2
14
16
11
I
Chip Select -2. Logical 0 on this pin provides the chip select-
2 function.
IOW
19
21
17
I
Write data strobe. Its function is the same as -IOW (see -
IOW), but it acts as an active high input signal. Either -IOW
or IOW is required to transfer data from the CPU to
ST16C450 during a write operation.
-AS
25
28
24
I
Address Strobe. A logic 0 transition on -AS latches the state
of the chip selects and the register select bits, A0-A2. This
input is used when address and chip selects are not stable
for the duration of a read or write operation, i.e., a micropro-
cessor that needs to de-multiplex the address and data bits.
If not required, the -AS input can be permanently tied to a
logic 0 (it is edge triggered).
D0-D7
1-8
2-9
43-47
2-4
I/O
Data Bus (Bi-directional) - These pins are the eight bit, tri-
state data bus for transferring information to or from the
controlling CPU. D0 is the least significant bit and the first
data bit in a transmit or receive serial data stream.
GND
20
22
18
Pwr
Signal and Power Ground.
SYMBOL DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452IJ68-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C454IJ68TR-F | IC UART QUAD 68PLCC |
| ST16C550CJ44-F | IC UART FIFO 16B SGL 44PLCC |
| ST16C550CP40-F | IC INTERFACE UART |
| ST16C552IJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C450CQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C450CQ48-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450CQ48TR-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C450IJ44-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。