- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1551IP28 (EXAR CORP) 2.97V TO 5.5V UART WITH 16-BYTE FIFO PDF資料下載
參數資料
| 型號： | ST16C1551IP28 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 17/37頁 |
| 文件大?。?/td> | 428K |
| 代理商： | ST16C1551IP28 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
á
REV. 4.2.0
ST16C1550/51
2.97V TO 5.5V UART WITH 16-BYTE FIFO
17
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when the
character has been received. LSR bits 2-4 generate an interrupt when the character with errors is read out of
the FIFO.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Reserved
IER[5]: Special Mode Enable
Logic 0 = Disable special mode functions (default).
Logic 1 = Enable special mode functions in addition to basic ST16C1450 functions. Enables ISR bits 4-5
(TXRDY/RXRDY), MCR bit-2 (soft reset) and MCR bit-7 (power down) functions.
IER[7:6]: Reserved
4.4
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table,
Table 5
, shows the data values (bits 0-3) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3 and 4.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX trigger level or TX FIFO empty.
MSR is by any of the MSR bits 0, 1, 2 and 3.
4.4.2
Interrupt Clearing:
LSR interrupt is cleared by a read to the LSR register (but flags and tags not cleared until character(s) that
generated the interrupt(s) has been emptied or cleared from FIFO).
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR until empty.
TXRDY interrupt is cleared by a read to the ISR register AND disabling the TXRDY interrupt (set IER bit-1 =
0), or by loading data into the TX FIFO.
MSR interrupt is cleared by a read to the MSR register.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1551IQ48 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C2450 | 2.97V TO 5.5V DUART |
| ST16C2450CJ44 | 2.97V TO 5.5V DUART |
| ST16C2450CP40 | 2.97V TO 5.5V DUART |
| ST16C2450CQ48 | 2.97V TO 5.5V DUART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1551IQ48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1551IQ48-F | 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2450 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART |
| ST16C2450_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART |
| ST16C2450CJ-0A-EB | 功能描述:界面開發工具 Supports C2450 44 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。