參數資料
型號: ST16C1551CJ28
廠商: EXAR CORP
元件分類: Serial IO/Communication Controller
英文描述: 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC28
封裝: PLASTIC, LCC-28
文件頁數: 16/38頁
文件大?。?/td> 622K
代理商: ST16C1551CJ28
xr
ST16C1550/51
REV. 4.2.1
2.97V TO 5.5V UART WITH 16-BYTE FIFO
23
4.9
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface input signals. Lower four bits of this register are
used to indicate the changed information. These bits are set to a logic 1 whenever a signal from the modem
changes state. These bits may be used for general purpose inputs when they are not used with modem
signals.
MSR[0]: Delta CTS# Input Flag
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
MSR[1]: Delta DSR# Input Flag
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[4]: CTS Input Status
CTS# (active high, logical 1). Normally this bit is the compliment of the CTS# input. In the loopback mode, this
bit is equivalent to bit-1 in the MCR register. The CTS# input may be used as a general purpose input when the
modem interface is not used.
MSR[5]: DSR Input Status
DSR# (active high, logical 1). Normally this bit is the compliment of the DSR# input. In the loopback mode, this
bit is equivalent to bit-0 in the MCR register. The DSR# input may be used as a general purpose input when the
modem interface is not used.
MSR[6]: RI Input Status
RI# (active high, logical 1). Normally this bit is the compliment of the RI# input. In the loopback mode this bit is
equivalent to bit-2 in the MCR register. The RI# input may be used as a general purpose input when the
modem interface is not used.
MSR[7]: CD Input Status
CD# (active high, logical 1). Normally this bit is the compliment of the CD# input. In the loopback mode this bit
is equivalent to bit-3 in the MCR register. The CD# input may be used as a general purpose input when the
modem interface is not used.
4.10
Scratch Pad Register (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
相關PDF資料
PDF描述
ST16C2552CJ44 2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44
ST16C552CJ68 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68
ST16C554DCJ68 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68
ST1803DHI High Voltage Fast-Switching NPN Power Transistor(高電壓快速開關NPN功率晶體管)
ST180S16P1PBF 314 A, 1600 V, SCR, TO-209AB
相關代理商/技術參數
參數描述
ST16C1551CJ28-F 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C1551CP28 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 16-BYTE FIFO
ST16C1551CQ48 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 16-BYTE FIFO
ST16C1551CQ48-F 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C1551IJ28 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: