- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1450IP28 (EXAR CORP) 2.97V TO 5.5V UART PDF資料下載
參數資料
| 型號： | ST16C1450IP28 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.97V TO 5.5V UART |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 355K |
| 代理商： | ST16C1450IP28 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
á
REV. 4.2.0
ST16C1450/51
2.97V TO 5.5V UART
15
4.0
INTERNAL REGISTER DESCRIPTIONS
4.1
See “Receiver” on page 10.
4.2
Transmit Holding Register (THR) - Write-Only
See “Transmitter” on page 9.
4.3
Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR).
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the THR is empty. If the THR is empty
when this bit is enabled, an interrupt will be generated. Note that this interrupt does not behave in the same
manner as the industry standard 16C550.
See “Interrupt Clearing:” on page 16.
Logic 0 = Disable Transmit Ready interrupt (default).
Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in the RHR.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Reserved
IER[5]: Special Mode Enable
Logic 0 = Disable special mode functions (default).
Logic 1 = Enable special mode functions in addition to basic ST16C1450 functions. Enables ISR bits 4-5
(TXRDY/RXRDY), MCR bit-2 (soft reset) and MCR bit-7 (power down) functions.
IER[7:6]: Reserved
4.4
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table,
Table 4
, shows the data values (bits 0-3) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
Receive Holding Register (RHR) - Read- Only
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1450IQ48 | 2.97V TO 5.5V UART |
| ST16C1451CJ28 | 2.97V TO 5.5V UART |
| ST16C1451CP28 | 2.97V TO 5.5V UART |
| ST16C1451CQ48 | 2.97V TO 5.5V UART |
| ST16C1451IJ28 | 2.97V TO 5.5V UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1450IQ48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1450IQ48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1450IQ48TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 1Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C1450IQ48TR-F |
| ST16C1451 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1451CJ28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
發布緊急采購，3分鐘左右您將得到回復。