- 您現在的位置：買賣IC網 > PDF目錄1969 > SP503EM-L (Exar Corporation)IC TXRX MULTIPROTOCOL 80LQFP PDF資料下載
參數資料
| 型號： | SP503EM-L |
| 廠商： | Exar Corporation |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX MULTIPROTOCOL 80LQFP |
| 標準包裝： | 84 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 7/7 |
| 規程： | 多協議 |
| 電源電壓： | 5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
SP503_101_101508
SP503 Multiprotocol Transceiver
Copyright 2008 Exar Corporation
12
There are three basic types of receivers —
RS-232, RS-423, and RS-485. The RS-232
receiver is a single–ended input with a threshold
of 0.8V to 2.4V. The RS-232 receiver has an
operating voltage range of ±15V and can re-
ceive signals up to 120kbps. RS-232 receivers
are used in RS-232 mode for all signal types,
and in V.35 mode for control line signals.
The RS-423 receivers are also single–ended but
have an input threshold as low as ±200mV. The
input impedance is guaranteed to be greater than
4k
, with an operating voltage range of ±7V.
The RS-423 receivers can operate up to 120kbps.
RS-423 receivers are used for the IC signal in
RS-449 and EIA-530 modes, as shown in Table
2.
The third type of receiver supports RS-485,
which is a differential interface mode. The
RS-485 receiver has an input impedance of
15k
and a differential threshold of ±200mV.
Since the characteristics of an RS-422 receiver
are actually subsets of RS-485, the receivers for
RS-422 requirements are identical to the
RS-485 receivers. RS-422 receivers are used in
RS-449 and EIA-530 for receiving clock, data,
and some control line signals. The RS-485
receivers are also used for the V.35 mode. V.35
levels require the ±0.55V signals with a load of
100
. In order to meet the V.35 input imped-
ance of 100
, the external termination network
Pin Label
Mode:
RS-232
V.35
RS-422
RS-485
RS-449
EIA-530
RDEC
3–RDEC0
0000
0010
1110
0100
0101
1100
1101
RD(a)
Undefined
RS-232
V.35–
RS-422–
RS-485–
RS-422–
RD(b)
Undefined
15k
to GND
V.35+
RS-422+
RS-485+
RS-422+
RT(a)
Undefined
RS-232
V.35–
RS-422–
RS-485–
RS-422–
RT(b)
Undefined
15k
to GND
V.35+
RS-422+
RS-485+
RS-422+
CS(a)
Undefined
RS-232
RS-422–
RS-485–
RS-422–
CS(b)
Undefined
15k
to GND
15k
to GND
RS-422+
RS-485+
RS-422+
DM(a)
Undefined
RS-232
RS-422–
RS-485–
RS-422–
DM(b)
Undefined
15k
to GND
15k
to GND
RS-422+
RS-485+
RS-422+
RR(a)
Undefined
RS-232
RS-422–
RS-485–
RS-422–
RR(b)
Undefined
15k
to GND
15k
to GND
RS-422+
RS-485+
RS-422+
IC(a)
Undefined
RS-232
RS-422–
RS-485–
RS-423
IC(b)
Undefined
15k
to GND
15k
to GND
RS-422+
RS-485+
15k
to GND
15k
to GND
SCT(a)
Undefined
RS-232
V.35–
RS-422–
RS-485–
RS-422–
SCT(b)
Undefined
15k
to GND
V.35+
RS-422+
RS-485+
RS-422+
Receivers
The SP503 has seven (7) independent receivers
which can be programmed for six (6) different
interface modes. One of the seven (7) receivers
(SCT) has an active–high enable control, as
shown in the Mode Diagrams.
Control for the mode selection is done via a 4–
bit control word that is independent from the
driver control word. The coding for the drivers
and receivers is identical. Therefore, if the modes
for the drivers and receivers are supposed to be
identical in the application, the control lines can
be tied together.
Like the drivers, the receivers are pre-arranged
for the specific requirements of the interface. As
the operating mode of the receivers is changed,
the electrical characteristics will change to sup-
port the requirements of clock, data, and control
line receivers. Table 2 shows a summary of the
electrical characteristics of the receivers in the
different interface modes. Unused receiver in-
puts can be left floating without causing oscilla-
tion. To ensure a desired state of the receiver
output, a pull–up resistor of 100k
to +5V
should be connected to the inverting input for a
logic low, or the non–inverting input for a logic
high. For single-ended receivers, a pull–down
resistor to ground of 5k
is internally con-
nected, which will ensure a logic high output.
Table 2. SP503 Receivers
相關PDF資料 |
PDF描述 |
|---|---|
| SP504MCM-L | IC TXRX WAN MULTI-MODE 80LQFP |
| SP505BCM-L | IC TXRX WAN MULTI-MODE 80LQFP |
| SP506CM-L | IC TXRX WAN MULTI-MODE 80LQFP |
| SP507CM-L | IC TXRX WAN MULTI-MODE 80LQFP |
| SP508EF-L | IC TXRX MULTIPROTOCOL 100LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP503P | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:LIQUID CRYSTAL DISPLAYS(STANDARD PRODUCTS) |
| SP504 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:WAN Multi-Mode Serial Transceiver |
| SP504AN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Application Note |
| SP504CF | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Application Note |
| SP504EB | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
發布緊急采購，3分鐘左右您將得到回復。