- 您現在的位置：買賣IC網 > PDF目錄384924 > SMM766 (Summit Microelectronics, Inc.) Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ PDF資料下載
參數資料
| 型號： | SMM766 |
| 廠商： | Summit Microelectronics, Inc. |
| 英文描述： | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
| 中文描述： | 六通道有源直流輸出控制器，監視器，Marginer和音序器的序列連接⑩ |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 970K |
| 代理商： | SMM766 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
SMM766
Preliminary Information
Summit Microelectronics, Inc
2086 2.1 12/13/2005
15
A pulse of current either sourced or sunk for 5μs every
1.7ms, to the capacitors connected to the TRIM_CAP
X
pins adjusts the voltage output on the TRIM
X
pins.
The voltages on the TRIM_CAP
X
pins are buffered
and applied to the TRIM
X
pins. The voltage
adjustments on the TRIM
X
pins cause a slight ripple of
less than 1mV on the power supply voltages. The
amplitude of this ripple is a function of the TRIM_CAP
capacitor and the trim gain of the converter.
Application Note 37 details the calculation of the
TRIM_CAP capacitor to achieve a desired minimum
ripple.
Each channel can be programmed to either enable or
disable the ADOC function. When disabled or not
active, the TRIM
X
pins on the SMM766 are high
impedance inputs. If disabled and not used, they can
be connected to ground. The voltages on the TRIM
X
pins are buffered and applied to the TRIM_CAP
X
pins
charging the capacitors. This allows a smooth
transition from the converter powering up to its
nominal voltage, to the SMM766 controlling that
voltage, and to the ADOC nominal setting.
The pulse of current can be increased to a 10X pulse
of current until the power supply voltages are at their
nominal settings by selecting the programmable Fast
Margin option. As the name implies, this option
decreases the time required to bring a supply voltage
from the converter’s nominal output voltage to the
ADOC nominal, high, or low voltage setting.
POWER-ON CASCADE SEQUENCING
The SMM766 can be programmed to sequence on 48
supplies occupying up to 29 sequence positions. This
is accomplished using the SEQ_LINK pin. Each of the
6 channels (A-F) on a SMM766 has an associated
open drain PUP output that, when connected to a
converter’s enable pin, controls the turn-on of the
converter. The channels are assigned sequence
positions to determine the order of the sequence. The
polarity of each of the PUP
X
outputs is programmable
for use with various types of converters.
Power-on sequencing is initiated on the rising edge of
the PWR_ON pin.
The SMM766 can be programmed to wait until any or
all VDD, 12VIN, and Internal Temp (Internal
Temperature) ADC readings are within their respective
voltage threshold or temperature limits before power-
on sequencing is allowed to begin. This ensures that
the converters have reached their full supply voltage
before they are enabled.
On the rising edge of the PWR_ON pin the SMM766
will wait a power-on delay time (t
DPON
) for any
channels in the first sequence position (position 1) and
then activate the PUP
X
outputs for those channels.
The
power-on
delay
programmable for each channel. The SMM766 will
then wait until all VM
X
inputs of the channels assigned
to the first sequence position are above their user
programmable UV1 thresholds, which is called
cascade sequencing.
At this point, the SMM766 will enter the second
sequence position (position 2) and begin to timeout
the power-on delay times for the associated channels.
This process continues until all of the channels
assigned to participate in the sequence have turned
on and are above their UV1 threshold. Once the
sequence has completed the status register indicates
that all sequenced power supply channels have turned
on. After the sequence has completed the SMM766
will begin the ADOC of the enabled channels. The
power-on sequencing mode ends when the ADOC
channels are at their nominal voltage setting. The
“Ready” bit in the status register signifies that the
voltages are at their set points.
The programmable sequence termination timer can be
used to protect against a stalled power-on sequence.
This timer resets itself at the beginning of each
sequence position. All channels in the sequence
position must go above their UV1 threshold before the
sequence termination timer times out (t
STT
) or the
sequence will terminate by pulling the FS# pin low,
initiating a Force Shutdown. The status register
contains bits indicating in which sequence position the
timer timed out. This sequence termination timer has
four settings of OFF, 100ms, 200ms and 400ms.
While the SMM766 is in the power-on sequencing
mode the RST# output is held active and the
HEALTHY output is held inactive regardless of trigger
sources (Figure 8). The power-off and force-shutdown
trigger options are also disabled while in this mode.
Furthermore, the SMM766 will not respond to activity
on the PWR_ON pin or to a power-off I
2
C command
during power-on sequencing mode.
The SMM766 permits multiple supplies to occupy the
same sequence position. When a sequence position is
shared, each channel will be enabled after its
respective power-on delay. When the last channel
occupying a shared sequence position exceeds its
UV1 setting the SMM766 will increment to the next
times
are
individually
APPLICATIONS INFORMATION (CONTINUED)
相關PDF資料 |
PDF描述 |
|---|---|
| SMM766FCR0 | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
| SMM766FCR1 | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
| SMM766FCR2 | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
| SMM766FCR3 | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
| SMM766FCR4 | Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMM766_11 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Linka?￠ |
| SMM766B | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link |
| SMM766B_11 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Linka?￠ |
| SMM766FC-251L | 制造商:SUMMIT MICROELECTRONICS 功能描述:POWER MGR 6 CH SEQ/MARGINER 48TQFP 制造商:SUMMIT MICROELECTRONICS 功能描述:POWER MGR, 6 CH SEQ/MARGINER, 48TQFP |
| SMM766FCR0 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Six-Channel Active DC Output Controller, Monitor, Marginer and Sequencer with Sequence-Link⑩ |
發布緊急采購，3分鐘左右您將得到回復。