- 您現在的位置：買賣IC網 > PDF目錄384923 > SMM150ER00 (Summit Microelectronics, Inc.) Single-Channel Supply Voltage Marginer/Monitor PDF資料下載
參數資料
| 型號： | SMM150ER00 |
| 廠商： | Summit Microelectronics, Inc. |
| 英文描述： | Single-Channel Supply Voltage Marginer/Monitor |
| 中文描述： | 單通道電源電壓Marginer /監視器 |
| 文件頁數： | 2/22頁 |
| 文件大?。?/td> | 388K |
| 代理商： | SMM150ER00 |
SMM150
GENERAL DESCRIPTION
The SMM150 is capable of margining the DC output
voltage of LDOs or DC/DC converters that use a
trim/adjust pin. The Margin function is programmable
over a standard 2-wire I
C serial data interface and is
used to set the margin low/high DC output voltages.
In margining mode the user communicates with the
SMM150 via the I
2
C serial data bus to select the
desired values for margining. This allows the part to
margin the supplies up or down to these set values
either through asserting the MUP and MDN pins or by
writing to the margin register directly. The margin high
and margin low voltage settings can range from 0.3V
to VDD around the converter’s nominal output voltage
setting depending on the specified margin range of the
DC-DC converter and/or system components, usually
±
10%.
When the SMM150 receives the command to margin,
the TRIM output will begin adjusting the supply to the
selected margin voltage. This is accomplished by
incrementing (or decrementing) an internal counter
based on the digital comparison between the voltage
margin target value and that read by the ADC from the
Preliminary Information
Summit Microelectronics, Inc
2075 2.6 05/13/05
2
VM input. This operation is repeated until the 2 values
are equal, after which the SMM150 holds the TRIM
output pin at the voltage required to maintain the
margin setting. An I
2
C command or de-assertion of the
MUP/MDN pin will return the TRIM output pin to a high
impedance state thus allowing the converter to return
to its nominal operating voltage.
The SMM150 has two additional input pins and one
additional output pin. The input pins, COMP1 and
COMP2, are high impedance inputs, each connected
to a comparator and compared against the internal
reference (VREF, 0.5V or 1.25V). Each comparator
can be independently programmed to monitor for UV
or OV. When either of the COMP1 or COMP2 inputs
are in fault the open-drain FAULT# output will be
pulled low. A configuration option exists to disable the
FAULT# output during margining.
Programming of the SMM150 is performed over the
industry standard I
2
C 2-wire serial data interface. A
status register is available to read the state of the part
and a Write Protect (WP) pin is available to prevent
writing to the configuration registers and EE memory.
相關PDF資料 |
PDF描述 |
|---|---|
| SMM150ER01 | Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER02 | Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER03 | Single-Channel Supply Voltage Marginer/Monitor |
| SMM465FCR02 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMM150ER01 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER02 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER03 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER04 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Single-Channel Supply Voltage Marginer/Monitor |
| SMM150ER05 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Single-Channel Supply Voltage Marginer/Monitor |
發布緊急采購，3分鐘左右您將得到回復。