- 您現在的位置：買賣IC網 > PDF目錄385849 > SMD84065013A (Intersil Corporation) CMOS Programmable Interval Timer PDF資料下載
參數資料
| 型號： | SMD84065013A |
| 廠商： | Intersil Corporation |
| 英文描述： | CMOS Programmable Interval Timer |
| 中文描述： | CMOS可編程間隔定時器 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 142K |
| 代理商： | SMD84065013A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁
4-11
FIGURE 13. MODE 4
Mode 5: Hardware Triggered Strobe (Retriggerable)
OUT will initially be high. Counting is triggered by a rising
edge of GATE. When the initial count has expired, OUT will
go low for one CLK pulse and then go high again.
After writing the Control Word and initial count, the counter
will not be loaded until the CLK pulse after a trigger. This
CLK pulse does not decrement the count, so for an initial
count of N, OUT does not strobe low until N + 1 CLK pulses
after trigger.
A trigger results in the Counter being loaded with the initial
count on the next CLK pulse. The counting sequence is trig-
gerable. OUT will not strobe low for N + 1 CLK pulses after
any trigger GATE has no effect on OUT.
If a new count is written during counting, the current count-
ing sequence will not be affected. If a trigger occurs after the
new count is written but before the current count expires, the
Counter will be loaded with new count on the next CLK pulse
and counting will continue from there.
FIGURE 14. MODE 5
Operation Common to All Modes
Programming
When a Control Word is written to a Counter, all Control
Logic, is immediately reset and OUT goes to a known initial
state; no CLK pulses are required for this.
Gate
The GATE input is always sampled on the rising edge of
CLK. In Modes 0, 2, 3 and 4 the GATE input is level sensi-
tive, and logic level is sampled on the rising edge of CLK. In
modes 1, 2, 3 and 5 the GATE input is rising-edge sensitive.
In these Modes, a rising edge of Gate (trigger) sets an edge-
sensitive flip-flop in the Counter. This flip-flop is then sam-
pled on the next rising edge of CLK. The flip-flop is reset
immediately after it is sampled. In this way, a trigger will be
detected no matter when it occurs - a high logic level does
not have to be maintained until the next rising edge of CLK.
Note that in Modes 2 and 3, the GATE input is both edge-
and level-sensitive.
N
N
N
N
0
2
0
1
0
0
FF
FF
FF
FE
FF
FD
0
3
WR
CLK
GATE
OUT
CW = 18
LSB = 3
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
CW = 18
LSB = 3
CW = 18
LSB = 3
N
N
N
0
3
0
2
0
1
0
2
0
1
0
0
FF
FF
N
N
N
N
0
3
0
3
0
2
0
1
0
0
FF
FF
0
3
LSB = 2
N
N
N
N
N
0
3
0
2
0
1
0
0
FF
FF
0
3
WR
CLK
GATE
OUT
CW = 1A LSB = 3
N
N
N
N
0
3
0
2
0
3
0
2
0
1
N
N
N
N
0
3
0
2
0
1
0
0
FF
FF
FF
FE
CLK
GATE
OUT
CW = 1A LSB = 3
WR
CLK
GATE
OUT
CW = 1A LSB = 3
N
N
N
0
0
FF
FF
LSB = 5
N
0
5
0
4
82C54
相關PDF資料 |
PDF描述 |
|---|---|
| SMD8406501JA | CMOS Programmable Interval Timer |
| SMI-42 | SMD POWER INDUCTORS |
| SMI-42-100 | SMD POWER INDUCTORS |
| SMI-42-101 | SMD POWER INDUCTORS |
| SMI-42-102 | SMD POWER INDUCTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMD8406501JA | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS Programmable Intervel Timer |
| SM-D-850489-2 | 制造商:Honeywell Sensing and Control 功能描述:CUSTOM POTENTIOMETER GS8363 |
| SM-D-859778 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| SM-D-859778 [PL150-29] | 制造商: 功能描述: 制造商:undefined 功能描述: |
| SM-D-869349 | 制造商:ITT Interconnect Solutions 功能描述:SM-D-869349 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。