參數資料
型號： SI3232PPTX-EVB
廠商： Silicon Laboratories Inc
文件頁數： 69/128頁
文件大?。?/td> 0K
描述： BOARD EVAL W/DISCRETE INTERFACE
標準包裝： 1
系列： ProSLIC®
主要目的： 接口，模擬前端（AFE）
已用 IC / 零件： Si3232
已供物品： 板，CD
Si3232
Preliminary Rev. 0.96
45
Not
Recommended
fo
r N
ew
D
esi
gn
s
4.12.1. Polarity Reversal
The Si3232 supports polarity reversal for message-
waiting functionality as well as various signaling modes.
The ramp rate can be programmed for a smooth
transition or an abrupt transition to accommodate
different application requirements. A wink function is
also provided for special equipment that responds to a
smooth ramp to VOC = 0 V. Table 27 illustrates the
register bits required to program the polarity-reversal
modes.
An immediate reversal (hard reversal) of the line polarity
is achieved by setting the Linefeed register to the
opposite polarity. For example, a transition from
Forward Active mode to Reverse Active mode is
achieved by changing LF[2:0] from 001 to 101. Polarity
reversal can also be accommodated in the OHT and
ground-start modes. The POLREV bit is a read-only bit
that reflects whether the device is in polarity reversal
mode. A smooth polarity reversal is achieved by setting
the PREN bit to 1 and setting the RAMP bit to 0 or 1
depending on the desired ramp rate (see Table 27).
Polarity reversal is then accomplished by toggling the
linefeed register from forward to reverse modes as
desired.
A wink function is used to slowly ramp down the TIP-
RING voltage (VOC) to 1 followed by a return to the
original VOC value (set in the VOC RAM 0 location).
This scheme is used to light a message-waiting lamp in
certain handsets. To enable this function, no change to
the linefeed register is necessary. Instead, the user
must set the VOCZERO bit to 1 to cause the TIP-RING
voltage to collapse to 0 V at the rate programmed by the
RAMP bit. Setting the VOCZERO bit back to 0 causes
the TIP-RING voltage to return to its normal setting. A
software timer provided by the user can automate the
cadence of the wink function. Figure 23 illustrates the
wink function.
Table 27. Register and RAM Locations used for Polarity Reversal
Parameter
Programmable Range
Register/RAM Bits
Location
Linefeed
LF[2:0]
LINEFEED
Polarity Reversal Status
Read only
POLREV
Wink Function
(Smooth transition to Voc = 0 V)
1 = Ramp to 0 V
0 = Return to previous VOC
VOCZERO
POLREV
Smooth Polarity Reversal Enable
0 = Disabled
1=Enabled
PREN
POLREV
Smooth Polarity Reversal Ramp
Rate
0=1 V/125s
1=2 V/125s
RAMP
POLREV
相關PDF資料
PDF描述
SI3216MDCQX-EVB DAUGHTER CARD W/DISCRETE INTRFC
M3TTK-3418J IDC CABLE - MSD34K/MC34G/MSD34K
A3BKB-3418G IDC CABLE- ASR34B/AE34G/APK34B
M3UMK-1036R IDC CABLE - MKS10K/MC10M/MCG10K
M1CXK-3440K IDC CABLE - MKC34K/MC34F/X
相關代理商/技術參數
參數描述
SI3232-X-FQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DUAL PROGRAMMABLE CMOS SLIC WITH LINE MONITORING
SI3232-X-GQ 制造商:SILABS 制造商全稱:SILABS 功能描述:DUAL PROGRAMMABLE CMOS SLIC WITH LINE MONITORING
SI3233 制造商:SILABS 制造商全稱:SILABS 功能描述:PROSLIC㈢ PROGRAMMABLE CMOS SLIC WITH RINGING/BATTERY VOLTAGE GENERATION
Si3233-C-FM 功能描述:射頻無線雜項 Single-Chan SLIC RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel
SI3233-C-FMR 功能描述:電信線路管理 IC Single-CH SLIC only BJT/inductor dc-dc RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*