參數資料
型號： SC415
廠商： Semtech Corporation
英文描述： Dual Synchronous Buck Controller
中文描述： 雙同步降壓控制器
文件頁數： 11/30頁
文件大?。?/td> 942K
代理商： SC415
SC415
11
Applications Information (continued)
The voltages available are shown:
FB Internal Voltage Selection
FB = RTN
1.5V
1.05V
FB = +5V
1.8V
1.25V
Side1
Side2
Enable/Psave Inputs
Each converter has a separate Enable pin. Each EN input
operates as follows:
EN = GND. This turns the converter off.
EN = open (float). This turns the converter on with psave
mode disabled (continuous conduction mode). In this
case, the EN pin will float to approximately 2V due to
an internal 1.5Meg/1Meg resistor divider from the +5V
supply at VDDx to ground.
EN = high (3.1V min). This turns the converter on with
psave mode enabled. At light loads, the converter will
operate in psave mode.
Note that the two EN pins are separate, so each output
can be disabled or operated with or without psave
independently.
If both EN1 and EN2 are grounded, the device is placed
into the lowest-power state, drawing typically 10μA from
the +5V supply.
PSAVE Operation
Each output provides automatic PSAVE operation at
light loads if the ENx pin is set high. The internal Zero-
Cross comparator looks for inductor current (via the
voltage across the lower MOSFET) to fall to zero on
eight consecutive switching cycles. Once observed,
the controller enters PSAVE mode and turns off the
low-side MOSFET on each subsequent cycle when the
current crosses zero. To add hysteresis, the on-time is also
increased by 25% when PSAVE mode is active, for that
output only; it does not affect the other converter. The
efficiency improvement at light loads more than offsets
the disadvantage of slightly higher output ripple. If the
inductor current does not cross zero on any switching
cycle, the controller immediately exits PSAVE. Once PSAVE
is exited, it requires 8 switching cycles at light load to re-
enter PSAVE. Since the controller counts zero crossings,
the converter can sink current as long as the current does
not cross zero on eight consecutive cycles. This allows the
output voltage to recover quickly in response to negative
load steps.
When operating in PSAVE mode at light loads, the LX
waveform will not have the typical square wave shape
seen when operating in continuous conduction mode.
Shortly after DL drives low, and both MOSFETs are off, the
LX voltage will show ringing. This ringing is caused by the
LC circuit formed by the inductor and device capacitance
of the MOSFETs and low-side diode. When the low-
side MOSFET turns off the inductor current falls toward
zero. When it reaches zero, the inductance and MOSFET
capacitances will tend to ring freely. This is normal PSAVE
operation as shown in Figure 3:
VOUT
VIN
COUT
L
C
Q1
C
Q2
Q1
Q2
DH
DL
DL
LX
VOUT
VIN
Typical ringing at LX
Figure 3
相關PDF資料
PDF描述
SC415EVB Dual Synchronous Buck Controller
SC415MLTRT Dual Synchronous Buck Controller
SC416 Dual Synchronous Buck Controller with Tracking Start-up/Shutdown
SC416EVB Dual Synchronous Buck Controller with Tracking Start-up/Shutdown
SC416MLTRT Dual Synchronous Buck Controller with Tracking Start-up/Shutdown
相關代理商/技術參數
參數描述
SC415_08 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Dual Synchronous Buck Controller
SC4150 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller
SC4150HIS-4TRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller
SC4150HISTRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller
SC4150LIS-4TRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*