參數資料
型號： SC28C94A1A,518
廠商： NXP Semiconductors
文件頁數： 35/39頁
文件大?。?/td> 0K
描述： IC UART QUAD W/FIFO 52-PLCC
產品培訓模塊： Stand-Alone UARTs
標準包裝： 1
特點： 故障啟動位檢測
通道數： 4，QUART
FIFO's： 8 字節
電源電壓： 5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 52-LCC（J 形引線）
供應商設備封裝： 52-PLCC（19.2x19.2）
包裝： 標準包裝
產品目錄頁面： 828 (CN2011-ZH PDF)
其它名稱： 568-1114-6
Philips Semiconductors
Product data sheet
SC28C94
Quad universal asynchronous receiver/transmitter (QUART)
2006 Aug 09
5
PIN DESCRIPTION
MNEMONIC
TYPE
NAME AND FUNCTION
CEN
I
Chip Select: Active low input that, in conjunction with RDN or WRN, indicates that the host MPU is trying to
access a QUART register. CEN must be inactive when IACKN is asserted.
A5:0
I
Address Lines: These inputs select a 28C94 register to be read or written by the host MPU.
D7:0
I/O
8-bit Bidirectional Data Bus: Used by the host MPU to read and write 28C94 registers.
RDN
I
Read Strobe: Active low input. When this line is asserted simultaneously with CEN, the 28C94 places the
contents of the register selected by A5:0 on the D7:0 lines.
WRN
I
Write Strobe: Active low input. When this line is asserted simultaneously with CEN, the 28C94 writes the data
on D7:0 into the register selected by A5:0.
DACKN
O
Data ACKnowledge: Active low, open-drain output to the host MPU, which is asserted subsequent to a read or
write operation. For a read operation, assertion of DACKN indicates that register data is valid on D7:0. For a
write operation, it indicates that the data on D7:0 has been captured into the indicated register. This signal
corresponds to READYN on 80x86 processors and DTACKN on 680x0 processors.
IRQN
O
Interrupt Request: This active low open-drain output to the host MPU indicating that one or more of the
enabled UART interrupt sources has reached an interrupt value which exceeds that pre-programmed by host
software. The IRQN can be used directly as a 680x0 processor input; it must be inverted for use as an 80x86
interrupt input. This signal requires an external pull-up resistor.
IACKN
I
Interrupt ACKnowledge: Active low input indicates host MPU is acknowledging an interrupt requested. The
28C94 responds by placing an interrupt vector or interrupt vector modified on D7-D0 and asserting DACKN. This
signal updates the CIR register in the interrupt logic. CEN must be high during this cycle.
TDa-d
O
Transmit Data: Serial outputs from the four UARTs.
RDa-d
I
Receive Data: Serial inputs to the four UARTs/
I/O0a-d
I/O
Input/Output 0: A multi-use input or output signal for each UART. These pins can be used as general purpose
inputs, Clear to Send inputs, 1X or 16X Transmit Clock outputs or general purpose outputs. Change-of-state
detection is provided for these pins. I/O pins have approximately 1.5 Mohm pull–up device.
I/O1a-d
I/O
Input/Output 1: A multi-use input or output signal for each UART. These pins can be used as general purpose
or 1X or 16X transmit clock inputs, or general purpose 1X or 16X receive clock outputs. Change-of-state
detection is provided for these pins. In addition, I/O1a and I/O1c can be used as Counter/Timer inputs and I/O1b
and I/O1d can be used as Counter/Timer outputs. I/O pins have approximately 1.5 Mohm pull–up device.
I/O2a-d
I/O
Input/Output 2: A multi-use input or output signal for each UART. These pins can be used as general purpose
inputs, 1X or 16X receive clock inputs, general purpose outputs, RTS output or 1X or 16X receive clock outputs.
I/O pins have approximately 1.5 Mohm pull–up device.
I/O3a-d
I/O
Input/Output 3: A multi-use input or output signal for each UART. These pins can be used as general purpose
inputs, 1X or 16X transmit clock inputs, general purpose outputs, or 1X or 16X transmit clock outputs. I/O pins
have approximately 1.5 Mohm pull–up device.
RESET
I
Master Reset: Active high reset for the 28C94 logic. Must be asserted at power-up, may be asserted at other
times that the system is to be reset and restarted. OSC set to divide by 1, MR pointer set to 1, DACKN enabled,
I/O pins to input. Registers reset: MR0, OPR, CIR. IRQN, DTACKN, IVR Interrupt Vector, Power Down, Test
registers, FIFO pointers, Baud rate generator, Error Status, Watch Dog Timers, Change of State detectors,
counter/timer to timer, Transmitter and Receiver controllers and all interrupt bits. If reset pin is not used, then
first chip access should be to celar ‘power-down’ mode.
X1/CLK
I
Crystal 1 or Communication Clock: This pin is normally connected to one side of a 3.6864MHz or a
7.3728MHz crystal, or can be connected to an external clock up to 8MHz.
X2
O
Crystal 2: If a crystal is used, this pin should be connected to its other terminal. If an external clock is applied to
X1, this pin should be left unconnected.
VCC, VSS
Power and grounds: respectively.
COUNTER/TIMER
I/O PORT CONTROL
UARTS A/B
INTERRUPT CONTROL
BLOCK B
UARTS C/D
I/O CONTROL
I/O PORT CONTROL
A0-A5
D (7:0)
DTACKN
IACKN
BAUD
RATE
GENERATOR
BUS
INTERFACE
BLOCK A
SD00161
Figure 3. Channel Architecture
相關PDF資料
PDF描述
SC16C754BIA68,518 IC UART QUAD W/FIFO 68-PLCC
SC26C92C1N,602 IC UART DUAL W/FIFO 40-DIP
SC28L91A1B,551 IC UART SINGLE W/FIFO 44-PQFP
SC28L91A1B,528 IC UART SINGLE W/FIFO 44PQFP
SC28L91A1A,529 IC UART SINGLE W/FIFO 44-PLCC
相關代理商/技術參數
參數描述
SC28C94A1AB 制造商:PHILIPS-SEMI 功能描述:
SC28C94A1N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad universal asynchronous receiver/transmitter QUART
SC28C94A1N,112 功能描述:IC UART QUAD W/FIFO 48-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
SC28L194 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART for 3.3V and 5V supply voltage
SC28L194A1A 功能描述:UART 接口集成電路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*