- 您現在的位置：買賣IC網 > PDF目錄98078 > SC18IS600IBS (NXP SEMICONDUCTORS) I2C BUS CONTROLLER, PQCC24 PDF資料下載
參數資料
| 型號： | SC18IS600IBS |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | I2C BUS CONTROLLER, PQCC24 |
| 封裝： | 4 X 4 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT616-3, HVQFN-24 |
| 文件頁數： | 3/30頁 |
| 文件大小： | 164K |
| 代理商： | SC18IS600IBS |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
SC18IS600_601_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 28 July 2008
11 of 30
NXP Semiconductors
SC18IS600/601
SPI to I2C-bus interface
6.2.6 I2C-bus status register (I2CStat)
This register reports the results of I2C-bus transmit and receive transaction between
SC18IS600/601 and an I2C-bus slave device.
Table 8.
I2C-bus status
Register
value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
I2C-bus status description
0xF0
11110000Transmission successful. The SC18IS600/601
has successfully completed an I2C-bus read or
write transaction. An interrupt is generated on
INT. This is also the default status after reset. No
interrupt is generated after reset.
0xF1
11110001I2C-bus device address not acknowledged. No
I2C-bus slave device has acknowledged the slave
address that has been sent out in an I2C-bus read
or write transaction. An interrupt is generated on
INT.
0xF2
11110010I2C-bus device address not acknowledged. An
I2C-bus slave has not acknowledged the byte that
has just been transmitted by the SC18IS600/601.
An interrupt is generated on INT.
0xF3
11110011I2C-bus busy. The SC18IS600/601 is busy
performing an I2C-bus transaction, no new
transaction should be initiated by the host. No
interrupt is generated.
0xF8
time-out register (I2CTO)”). The SC18IS600/601
has started an I2C-bus transaction that has taken
longer than the time programmed in I2CTO
register. This could happen after a period of
unsuccessful arbitration or when an I2C-bus slave
is (continuously) pulling the SCL clock LOW. An
interrupt is generated on INT.)
0xF9
11111001I2C-bus invalid data count. The number of bytes
specied in a read or write command to the
SC18IS600/601. An interrupt is generated on INT.
相關PDF資料 |
PDF描述 |
|---|---|
| SC2200UCL-300 | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC2200UCL-300F | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC26C562A8A | 2 CHANNEL(S), 10M bps, MULTI PROTOCOL CONTROLLER, PQCC52 |
| SC26C92AA1A44 | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44 |
| SC26C92AC1F40 | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC18IS600IBS,128 | 功能描述:總線收發器 SPI to I2C Bus Interface 24-Pin RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SC18IS600IBS,151 | 功能描述:I2C 接口集成電路 SPI to I2C Bus Interface 24-Pin RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| SC18IS600IBS,157 | 功能描述:總線收發器 SPI to I2C Bus Interface 24-Pin RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SC18IS600IBS151 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SC18IS600IPW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SPI to IC-bus interface |
發布緊急采購，3分鐘左右您將得到回復。