參數資料
型號: SAK-XC2264-56F66L
廠商: INFINEON TECHNOLOGIES AG
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 66 MHz, MICROCONTROLLER, PQFP100
封裝: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-100
文件頁數: 112/116頁
文件大?。?/td> 1516K
代理商: SAK-XC2264-56F66L
XC2267 / XC2264
XC2000 Family Derivatives
Electrical Parameters
Data Sheet
93
V2.1, 2008-08
The timing in the AC Characteristics refers to TCSs. Timing must be calculated using the
minimum TCS possible under the given circumstances.
The actual minimum value for TCS depends on the jitter of the PLL. Because the PLL is
constantly adjusting its output frequency to correspond to the input frequency (from
crystal or oscillator), the accumulated jitter is limited. This means that the relative
deviation for periods of more than one TCS is lower than for a single TCS (see formulas
and Figure 19).
This is especially important for bus cycles using waitstates and for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is negligible.
The value of the accumulated PLL jitter depends on the number of consecutive VCO
output cycles within the respective timeframe. The VCO output clock is divided by the
output prescaler K2 to generate the system clock signal
f
SYS. The number of VCO cycles
is K2
× T, where T is the number of consecutive f
SYS cycles (TCS).
The maximum accumulated jitter (long-term jitter) DTmax is defined by:
DTmax [ns] = ±(220 / (K2 × fSYS) + 4.3)
This maximum value is applicable, if either the number of clock cycles T > (
f
SYS / 1.2) or
the prescaler value K2 > 17.
In all other cases for a timeframe of T
× TCS the accumulated jitter D
T is determined by:
DT [ns] = DTmax × [(1 - 0.058 × K2) × (T - 1) / (0.83 × fSYS - 1) + 0.058 × K2]
f
SYS in [MHz] in all formulas.
Example, for a period of 3 TCSs @ 33 MHz and K2 = 4:
Dmax = ±(220 / (4 × 33) + 4.3) = 5.97 ns (Not applicable directly in this case!)
D3 = 5.97 × [(1 - 0.058 × 4) × (3 - 1) / (0.83 × 33 - 1) + 0.058 × 4]
= 5.97
× [0.768 × 2 / 26.39 + 0.232]
= 1.7 ns
Example, for a period of 3 TCSs @ 33 MHz and K2 = 2:
Dmax = ±(220 / (2 × 33) + 4.3) = 7.63 ns (Not applicable directly in this case!)
D3 = 7.63 × [(1 - 0.058 × 2) × (3 - 1) / (0.83 × 33 - 1) + 0.058 × 2]
= 7.63
× [0.884 × 2 / 26.39 + 0.116]
= 1.4 ns
相關PDF資料
PDF描述
SAF-XC2387-72F66L 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PQFP144
SAF-XC2735X-72F80L RISC MICROCONTROLLER, PQFP64
SAF-XC2785X-104F80L 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
SAK-XC2785X-72F80L 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
SAK-XC2785X-104F80L 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
SAK-XC2264-56F66L AC 功能描述:IC MCU 16BIT FLASH PG-LQFP-100 RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:XC22xx 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C,SPI,UART/USART 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:21 程序存儲器容量:12KB(4K x 24) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
SAK-XC2264-56F66L34AC 制造商:Infineon Technologies AG 功能描述:
SAK-XC2264-56F66LAC 功能描述:16位微控制器 - MCU 16 BIT FLASH C11 BCS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-XC2264-72F66L 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16/32-Bit Single-Chip Microcontroller with 32-Bit Performance
SAK-XC2264-96F66L 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16/32-Bit Single-Chip Microcontroller with 32-Bit Performance