- 您現在的位置：買賣IC網 > PDF目錄385814 > SAB-C541U-1EP (SIEMENS A G) 8-Bit CMOS Microcontroller PDF資料下載
參數資料
| 型號： | SAB-C541U-1EP |
| 廠商： | SIEMENS A G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit CMOS Microcontroller |
| 中文描述： | 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PDIP52 |
| 文件頁數： | 42/65頁 |
| 文件大?。?/td> | 427K |
| 代理商： | SAB-C541U-1EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Semiconductor Group
42
1997-10-01
C540U
C541U
XTAL1
21
24
I
XTAL1
Input to the oscillator amplifier.
A0/A8 -
A7
24 - 31
28 - 35
I
Address lines
P2.0-7 are used as multiplexed address input lines
A0-A7 and A8-A12. A8-A12 must be latched with
PALE. Address A12 is requred only for the C541U.
PSEN
32
38
I
Program store enable
This input must be at static “0“ level during the whole
programming mode.
PROG
33
39
I
Programming mode write strobe
This input is used in programming mode as a write
strobe for OTP memory program and lock bit write
operations During basic programming mode selection
a low level must be applied to PROG.
EA/V
PP
35
42
I
External Access / Programming voltage
This pin must be at 11.5 V (V
PP
) voltage level during
programming of an OTP memory byte or lock bit.
During an OTP memory read operation this pin must
be at high level (V
IH
). This pin is also used for basic
programming mode selection. At basic programming
mode selection a low level must be applied to EA/V
PP
.
Data lines 0-7
During programming mode, data bytes are read or
written from or to the C540U/C541U via the
bidirectional D0-7 lines which are located at port 0.
D0 - 7
43 - 38
50 - 43
I/O
V
SS
9, 22
11, 25
–
Circuit ground potential
must be applied to these pins in programming mode.
V
CC
8, 23
10, 26
–
Power supply terminal
must be applied to these pins in programming mode.
N.C.
1, 12,,
34, 44
1 - 9, 14,
15, 27, 36,
37, 40, 41,
52
–
Not Connected
These pins should not be connected in programming
mode.
GND
17 - 19
20 - 22
I
Ground pins
In programming mode these pins must be connected
to
V
IL
level.
*) I = Input
O = Output
Table 9
Pin Definitions and Functions in Programming Mode
(cont’d)
Symbol
Pin Numbers
I/O*) Function
P-LCC-44 P-SDIP-52
相關PDF資料 |
PDF描述 |
|---|---|
| SAB-R2000A | MOSFET N-CH 300V 73A TO-264AA |
| SAB-R2000A-12-A | HIGH PERFORMANCE 32-BIT RISC MICROPROCESSOR |
| SAB-R2000A-16-A | MOSFET N-CH 200V 90A TO-264AA |
| SAB-R2000A-20-A | MOSFET N-CH 200V 50A TO-204AE |
| SAB-R2010A | MOSFET N-CH 200V 106A SOT-227B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-ABF03-P20-512 | 制造商:RadiSys 功能描述:2.0 PENTIUM M 512 GB |
| SABIE10-001 | 制造商:Synapse Wireless 功能描述:E10 WO/CASE, SNAP CONNECT SOFT 制造商:Synapse Wireless 功能描述:E10 NO CASE 制造商:Synapse Wireless 功能描述:custom board SLE10M-BOARD |
| SABIX A 200 FRNC 10G0,50 M | 制造商:SAB Broeckskes 功能描述:Roll |
| SABIX A 200 FRNC 12G0,50 M | 制造商:SAB Broeckskes 功能描述:Roll |
| SABIX A 200 FRNC 4G4,0 MM | 制造商:SAB Broeckskes 功能描述:Roll |
發布緊急采購，3分鐘左右您將得到回復。