- 您現在的位置：買賣IC網 > PDF目錄372108 > SAA2500 (NXP Semiconductors N.V.) MPEG Audio Source Decoder PDF資料下載
參數資料
| 型號： | SAA2500 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | MPEG Audio Source Decoder |
| 中文描述： | MPEG音頻源解碼器 |
| 文件頁數： | 34/47頁 |
| 文件大?。?/td> | 199K |
| 代理商： | SAA2500 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
September 1994
34
Philips Semiconductors
Preliminary specification
MPEG Audio Source Decoder
SAA2500
Operational address declaration
For the declaration (programming) of the operational
address of an L3 device with a ‘secondary L3 identification
code’ the following action is required:
1.
First the microcontroller must issue an L3 operational
address ‘000000’ (special function address) with
DOM1 = 0 and DOM0 = 1. This combination defines
the operational address declaration operation. Next
the microcontroller will start a data transfer mode in
which it first sends the secondary L3 identification
code for the device that is to be issued an operational
address, followed by a byte containing the operational
address (the DOM bits in this byte are don't cares).
2.
Next the microcontroller will start a data transfer mode
in which it first sends the secondary L3 identification
code for the device that is to be issued an operational
address, followed by a byte containing the operational
address (the DOM bits in this byte are don't cares).
A secondary L3 identification code is unique for any
design. Devices of the same design have the same
identification code of one or more bytes. However, special
designs may have a range of identification codes, one of
which can be selected by a hardware solution, to enable
the connection of more than one device of the same
design to the L3 interface. It is also possible to use
separate L3MODE lines for multiple devices of the same
design, but the same L3 identification code (this also
enables ‘parallel programming’ of these devices). Bit 0 of
any identification code byte will indicate whether or not an
additional byte follows:
Bit 0 = 0; no additional byte as part of the identification
code.
Bit 0 = 1; additional byte follows.
With this the number of secondary L3 identification codes
is (theoretically) unlimited.
The operational address for the programmable device is
preferable in the range 111000 to 111111. However, it is
possible in a given application to issue any operational
address that is not used to address primary L3 devices or
other secondary L3 devices. An example is given in
Table 33.
Table 33
Example of L3 devices; notes 1 to 4.
Notes
1.
2.
3.
4.
Bits are shown in the order they appear on L3DATA (bit 0 first, bit 7 last).
X = bit of the identification code.
M = DOM bit of operational address (don’t care).
Y = bit of the operational address.
ADDRESSING MODE
DATA MODE
SPECIAL ADDRESS
SECONDARY L3 IDENTIFICATION CODE
OPERATIONAL
ADDRESS
(ONE BYTE)
BYTE 1
BYTE 2
BYTE 3
10000000
1XXXXXXX
1XXXXXXX
0XXXXXXXX
MMYYYYYY
Operational address invalidation
In order to re-allocate an operational address that has
been allocated to a secondary L3 device it is possible to
invalidate an operational address:
First the microcontroller must issue an L3 operational
address ‘000000’ (special function address) with
DOM1 = 1 and DOM0 = 0. This combination defines the
operational address invalidation operation.
Next the microcontroller will start a data transfer mode in
which it only sends the secondary L3 identification code
for the device that will no longer be addressed. From this
moment on the device will not be able to communicate
with the microcontroller until it is issued a new
operational address by an OA declaration (it will enter a
‘device interface reset’ condition).
Remark: the combination of a special function address
(000000) and DOM1 and DOM0 equal to ‘1’ is reserved for
future applications. Designs based on this specification will
react with a ‘device interface reset’.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA2500H | MPEG Audio Source Decoder |
| SAA2501 | Digital Audio Broadcast DAB decoder |
| SAA2501H | Digital Audio Broadcast DAB decoder |
| SAA2502 | ISO/MPEG Audio Source Decoder |
| SAA2502H | ISO/MPEG Audio Source Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA2500GP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video Processing/ENDEC for MPEG |
| SAA2500H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:MPEG Audio Source Decoder |
| SAA2500HB-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video Processing/ENDEC for MPEG |
| SAA2501 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Audio Broadcast DAB decoder |
| SAA2501H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Audio Broadcast DAB decoder |
發布緊急采購，3分鐘左右您將得到回復。