- 您現在的位置：買賣IC網 > PDF目錄225144 > SA58632BS (NXP Semiconductors N.V.) 2 x 2.2 W BTL audio amplifier PDF資料下載
參數資料
| 型號： | SA58632BS |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 音頻放大器 |
| 英文描述： | 2 x 2.2 W BTL audio amplifier |
| 封裝： | SA58632BS<SOT910-1 (HVQFN20)|<<http://www.nxp.com/packages/SOT910-1.html<1<Always Pb-free,; |
| 文件頁數： | 7/28頁 |
| 文件大小： | 283K |
| 代理商： | SA58632BS |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
SA58632_2
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 — 4 March 2010
15 of 28
NXP Semiconductors
SA58632
2
× 2.2 W BTL audio amplifier
14.4 Single-ended application
Tamb = 25 °C; VCC = 7.5 V; f = 1 kHz; RL =8 Ω; Gv = 20 dB; audio band-pass 20 Hz to
20 kHz.
The single-ended application diagram is shown in Figure 15.
If the BTL/SE pin is to ground, the positive outputs (OUTL+, OUTR+) will be in mute
condition with a DC level of 0.5VCC. When a headphone is used (RL >25 Ω) the SE
headphone application can be used without coupling capacitors by placing the load
between negative output and one of the positive outputs (for example, pin 1) as the
common pin.
Increasing the value of the tantalum or electrolytic capacitor C3 will result in a better
channel separation. Because the positive output is not designed for high output current
(2
× I
O) at the load impedance (< 16 Ω), the SE application with output capacitors
connected to ground is advised. The capacitor value of C4/C5 in combination with the
load impedance determines the low frequency behavior. The total harmonic
distortion-plus-noise as a function of frequency was measured with a low-pass filter of
80 kHz. The value of the capacitor C3 influences the behavior of the PSRR at low
frequencies; increasing the value of C3 increases the performance of PSRR.
Pins 8, 9, 18 and 19 connected to ground.
Fig 15. SE application circuit configuration
002aac091
R2
100 k
Ω
SA58632
OUTL
INL+
INL
GND
SVR
OUTL+
MODE
7
15
14
3
2
16
1
17
C3
47
μF
R1
1
μF
VIL
100
μF
100 nF
VCC
20
10
R4
100 k
Ω
OUTR
INR+
INR
OUTR+
12
13
11
6
R3
1
μF
VIR
RL = 8 Ω
OUTR
BTL/SE
4
10 k
Ω
10 k
Ω
RL = 8 Ω
C4
470
μF
C5
470
μF
Gain left
R2
R1
-------
=
Gain right
R4
R3
-------
=
相關PDF資料 |
PDF描述 |
|---|---|
| SA58635UK | 2 x 25 mW class-G stereo headphone driver with I2C-bus volume control |
| SA58637BS | 2 x 2.2 W BTL audio amplifier |
| SA58670ABS | 2.1 W-channel stereo class-D audio amplifier |
| SA58670BS | 2.1 W-channel stereo class-D audio amplifier |
| SA58672TK | 3.0 W mono class-D audio amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA58632BS,118 | 功能描述:音頻放大器 2X2.2W BTL PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58632BS118 | 制造商:NXP Semiconductors 功能描述:IC AUDIO AMP AB 2.2W SON-20 |
| SA58632BS-T | 功能描述:音頻放大器 2X2.2W BTL PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58635UK,027 | 功能描述:音頻放大器 2x25mW cls-G stereo headphone driver RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58637 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 X 2.2 W BTL audio amplifier |
發布緊急采購，3分鐘左右您將得到回復。