- 您現在的位置：買賣IC網 > PDF目錄192300 > S29GL032M11TCIR42 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 110 ns, PDSO48 PDF資料下載
參數資料
| 型號： | S29GL032M11TCIR42 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 110 ns, PDSO48 |
| 封裝： | LEAD FREE, TSOP-48 |
| 文件頁數： | 158/160頁 |
| 文件大?。?/td> | 4727K |
| 代理商： | S29GL032M11TCIR42 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁當前第158頁第159頁第160頁
April 30, 2004 S29GLxxxM_00A5
S29GLxxxM MirrorBitTM Flash Family
97
Pre l i m i n a r y
tion of the SecSi Sector without raising any device pin to a high voltage. Note
that this method is only applicable to the SecSi Sector.
To verify the protect/unprotect status of the SecSi Sector, follow the algo-
rithm shown in Figure 1.
Once the SecSi Sector is programmed, locked and verified, the system must write
the Exit SecSi Sector Region command sequence to return to reading and writing
within the remainder of the array.
Factory Locked: SecSi Sector Programmed and Protected At the
Factory
In devices with an ESN, the SecSi Sector is protected when the device is shipped
from the factory. The SecSi Sector cannot be modified in any way. An ESN Factory
Locked device has an 16-byte random ESN at addresses 000000h–000007h.
Please contact your sales representative for details on ordering ESN Factory
Locked devices.
Customers may opt to have their code programmed by the factory through the
Spansion programming service (Customer Factory Locked). The devices are then
shipped from the factory with the SecSi Sector permanently locked. Contact your
sales representative for details on using the Spansion programming service.
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting the first or
last sector group without using VID. Write Protect is one of two functions provided
by the WP#/ACC input.
If the system asserts VIL on the WP#/ACC pin, the device disables program and
erase functions in the first or last sector group independently of whether those
sector groups were protected or unprotected. Note that if WP#/ACC is at VIL
when the device is in the standby mode, the maximum input load current is in-
creased. See the table in “DC Characteristics” section on page 122.
If the system asserts VIH on the WP#/ACC pin, the device reverts to
whether the first or last sector was previously set to be protected or un-
protected using the method described in “Sector Group Protection and
Unprotection”. Note that WP# has an internal pullup; when uncon-
nected, WP# is at VIH.
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing
provides data protection against inadvertent writes (refer to Tables 16 and 17 for
command definitions). In addition, the following hardware data protection mea-
sures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during VCC power-up and power-down
transitions, or from system noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This pro-
tects data during VCC power-up and power-down. The command register and all
internal program/erase circuits are disabled, and the device resets to the read
mode. Subsequent writes are ignored until VCC is greater than VLKO. The system
must provide the proper signals to the control pins to prevent unintentional writes
when VCC is greater than VLKO.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL064A10BAIW12 | 4M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| S29GL128N11FAIVH0 | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| S29GL128N11FFIVH2 | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| S29JL032J70TFI213 | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29PL032J65BFI150 | 2M X 16 FLASH 3V PROM, 65 ns, PBGA56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032M90FACR20 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 32MBIT 4MX8/2MX16 90NS 64BGA - Trays |
| S29GL032M90FACR30 | 制造商:Spansion 功能描述: |
| S29GL032M90TAIR40 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 32M-Bit 4M x 8/2M x 16 90ns 48-Pin TSOP Tray |
| S29GL032M90TFIR30 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 32M-Bit 4M x 8/2M x 16 90ns 48-Pin TSOP Tray |
| S29GL032M90TFIR40 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 32M-Bit 4M x 8/2M x 16 90ns 48-Pin TSOP Tray |
發布緊急采購，3分鐘左右您將得到回復。