參數資料
型號： S1M8660AX01-F0T0
元件分類： 通信及網絡
英文描述： SPECIALTY TELECOM CIRCUIT, CBCC48
封裝： 7 X 7 MM, BCC-48
文件頁數： 13/32頁
文件大?。?/td> 270K
代理商： S1M8660AX01-F0T0
S1M8660A (Preliminary)
RX IF/BBA WITH GPS
20
Serial Data Transfer format
S1M8660A and S1M8657 are all slave devices with the SPI bus. What differentiate them from one another is
their different device IDs. Each company has its own characteristic SPI bus configuration , but normally the 3-line
bus is most often used and sometimes the 2-line bus such as the IIC bus. Figure 13. shows the serial data
transfer format.
mode=01
Dummy
1=Master read
Master drive
Slave Address
Start bit
STB
CLK
DATA
D5 D4 D3 D2 D1 D0
D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
Master drive
Register
Address
Slave drive
data
Master drive
Register
Address
Master drive
data
End bit
Dummy
0=Master read
Dummy
Figure 13. Serial Data Transfer Format
(1)
The first 2-BITs are for transmission only and this product must send '01'.(Others are not permitted.)
(2)
The following 6-bit data specifies the slave device, which is connected to the SPI bus and has its own ID.
(3)
The following 1-bit is a dummy bit, which marks the end of the 8-bit data transmission and the beginning of
the next data to be sent.
(4)
The following 1-bit decides on whether the master will drive the data line or the slave will. If this bit is '1', the
master will drive , but if '0' the slave will drive the data line.
(5)
The following 7-bit data is the register address of the specified slave device; the 7-bits for an address allows
128 register addresses for slaves.
(6)
The following high 1-BIT data is a dummy data.
(7)
The following 8-BIT data is the data in the device to be driven.
(8)
The following 1-BIT data is a dummy data, which marks the end of the 8-bit data transmission and
beginning of the next data to be sent.
(9)
The following 1-bit decides on whether the master will drive the data line or the slave will. If this bit is '1', the
master will drive , but if '0' the slave will drive the data line.
(10) The following 7-bit data is the register address of the specified slave device.
(11) The following high 1-BIT data is a dummy data.
(12) The following 8-BIT data is the data in the device to be driven.
(Continous data transmission such as this can be ended with a 1-byte transmission or can be read/written
repeatedly.)
(13) After the last data is sent, the data line opens and becomes high;
(14) the CLK continues for half the 1-clock cycle and then becomes high;
(15) and the STB becomes high as soon as the clock becomes high and this marks the end of data transmission.
相關PDF資料
PDF描述
S1M8836X01-G0T0 PLL FREQUENCY SYNTHESIZER, 1000 MHz, CQCC24
S1P-SLV 1 CONTACT(S), FEMALE, TWO PART BOARD CONNECTOR, CRIMP
S1T0567X01-D0B0 TELECOM, TONE DECODER CIRCUIT, PDIP8
S1U2-12-RC 500 MHz - 2000 MHz RF/MICROWAVE SGL POLE SGL THROW SWITCH, 1.5 dB INSERTION LOSS
S2004VS2 4 A, 200 V, SCR, TO-251
相關代理商/技術參數
參數描述
S1M8662A 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:CDMA/PCS/GPS Triple Mode IF/ baseband IC
S1M8662AX01-F0T0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:CDMA/PCS/GPS Triple Mode IF/ baseband IC
S1M8821 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL
S1M8821X01-R0T0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL
S1M8822 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*