- 您現在的位置：買賣IC網 > PDF目錄299876 > S-93C56BD0I-I8T1G 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | S-93C56BD0I-I8T1G |
| 元件分類： | PROM |
| 英文描述： | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封裝： | LEAD FREE, SNT-8 |
| 文件頁數： | 4/48頁 |
| 文件大?。?/td> | 803K |
| 代理商： | S-93C56BD0I-I8T1G |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
CMOS SERIAL E2PROM
S-93C46B/56B/66B
Rev.5.0_00
Seiko Instruments Inc.
12
Operation
All instructions are executed by inputting DI in synchronization with the rising edge of SK after CS goes
high. An instruction set is input in the order of start bit, instruction, address, and data.
Instruction input finishes when CS goes low. A low level must be input to CS between commands during
tCDS. While a low level is being input to CS, the S-93C46B/56B/66B is in standby mode, so the SK and DI
inputs are invalid and no instructions are allowed.
Start Bit
A start bit is recognized when the DI pin goes high at the rise of SK after CS goes high. After CS goes high,
a start bit is not recognized even if the SK pulse is input as long as the DI pin is low.
1. Dummy clock
SK clocks input while the DI pin is low before a start bit is input are called dummy clocks. Dummy
clocks are effective when aligning the number of instruction sets (clocks) sent by the CPU with those
required for serial memory operation. For example, when a CPU instruction set is 16 bits, the number
of instruction set clocks can be adjusted by inserting a 7-bit dummy clock for the S-93C46B and a 5-bit
dummy clock for the S-93C56B/66B.
2. Start bit input failure
When the output status of the DO pin is high during the verify period after a write operation, if a high
level is input to the DI pin at the rising edge of SK, the S-93C46B/56B/66B recognizes that a start bit
has been input. To prevent this failure, input a low level to the DI pin during the verify operation
period (refer to “4.1 Verify operation”).
When a 3-wire interface is configured by connecting the DI input pin and DO output pin, a period in
which the data output from the CPU and the serial memory collide may be generated, preventing
successful input of the start bit. Take the measures described in “
3-Wire Interface (Direct
Connection between DI and DO)
”.
相關PDF資料 |
PDF描述 |
|---|---|
| S-I6117#01 | 6A, 250VAC, FEMALE AND MALE, MAINS POWER CONNECTOR |
| S-T111B23MC-OGI-TF | 2.3 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| S02-BDS-3-B(LF)(SN) | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
| S02-BDS-3-B | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
| SM02-BDS-3-TB(LF)(SN) | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-93C56BD0I-I8T1U | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:3-WIRE SERIAL E2PROM |
| S-93C56BD0I-J8T1 | 制造商:Seiko Instruments Inc (SII) 功能描述: |
| S-93C56BD0I-J8T1G | 功能描述:電可擦除可編程只讀存儲器 2K (128X16) Hi-Speed RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| S-93C56BD0I-J8T1U | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:3-WIRE SERIAL E2PROM |
| S-93C56BD0I-J8T2G | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
發布緊急采購，3分鐘左右您將得到回復。