- 您現在的位置：買賣IC網 > PDF目錄374612 > S-4520BA (Seiko Instruments Inc.) Dot Matrix LCD Driver(點陣LCD驅動器) PDF資料下載
參數資料
| 型號： | S-4520BA |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | Dot Matrix LCD Driver(點陣LCD驅動器) |
| 中文描述： | 點陣LCD驅動器（點陣液晶驅動器） |
| 文件頁數： | 7/23頁 |
| 文件大小： | 160K |
| 代理商： | S-4520BA |
DOT MATRIX LCD DRIVER
S-4520BA
6
Seiko Instruments Inc.
Operation
1. Power-on
After power-on, initialization is executed by either the rising or the falling edge of the RESX input. MPU Interface
mode is selected by the level after RESX signal changes.
When initialization by RESX and the selection of an interface are not executed at power-on, a malfunction may
occur. Since chattering in RESX causes poor initializaition and erroneous selection of MPU interface, input the
signal without chattering. For details, refer to Reset and MPU Interface Selection in this section.
2. Reset
The S-4520BA can be initialized through RESX input or Reset command.
The initialization items through RESX input are listed in Table 9. Initialization through RESX input is executed at
the signal change point, either rising or falling. At that time, it is possible to select the MPU Interface. When
executing RESX input during operation at power-on, it is necessary to set the signal polarity to fixed MPU.
Initialization through Reset command executes , , and in Table 9. Be aware of the difference in
initialization items between reset through RESX input and initialization through Reset command.
Table 9
Initialization at power-on
Item
Status
Display
Display Start Line Set
Display all-lit
Column Address Counter
Page Address Register
Duty Select
ADC Select
Read Modify Write
OFF
1st
OFF
0
3
1/32
Forward
OFF
3. MPU interface selection
The selection of the S-4520B Series interface is determined by RESX signal logic after RESX signal input.
It is possible to connect directly to either the 68 family or the 80 family MPU
.
Table 10
Interface
Pin
73
76
77
79
～
86
68 family
80 family
A
0
A
0
E
R/WX
WRX
D
0
～
D
7
D
0
～
D
7
RDX
80 family interface setting
RESX
RESX
68 family interface setting
Initialization
相關PDF資料 |
PDF描述 |
|---|---|
| S-4525BACA | DOT MATRIX LCD DRIVER |
| S-4525BACG | DOT MATRIX LCD DRIVER |
| S-4525BA | Dot Matrix LCD Driver(點陣LCD驅動器) |
| S-4543A | Dot Matrix LCD Driver(點陣LCD驅動器) |
| S-4544A | LCD Controller-Driver With Built-in 8-Bit and Serial Interfaces(內置8位和串行接口的LCD控制器-驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-4520BACA | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:DOT MATRIX LCD DRIVER |
| S-4520BACG | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:DOT MATRIX LCD DRIVER |
| S4520C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:30-VOLT DICHROIC LCD DRIVER |
| S4520D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:30-VOLT DICHROIC LCD DRIVER |
| S4520E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:30-VOLT DICHROIC LCD DRIVER |
發布緊急采購，3分鐘左右您將得到回復。