- 您現在的位置：買賣IC網 > PDF目錄384884 > RF2668 (RF MICRO DEVICES INC) CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER WITH INTEGRATED PLL PDF資料下載
參數資料
| 型號： | RF2668 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER WITH INTEGRATED PLL |
| 中文描述： | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT |
| 封裝： | 7 X 7 MM, PLASTIC, LQFP-48 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 430K |
| 代理商： | RF2668 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Preliminary
5-76
RF2668
Rev B4 010423
5
M
U
Pin
17
Function
AGC_DEC
Description
AGC decoupling pin. An external bypass capacitor of 1nF capacitor is
required. The trace length between the pin and the bypass capacitors
should be minimized. The ground side of the bypass capacitors should
connect immediately to ground plane.
Analog gain control for AGC amplifiers. Valid control voltage ranges are
from 0.3V
DC
to 2.4V
DC
. The gain range for the AGC is 95dB. These
voltages are valid ONLY for a 39k
source impedance. A DC voltage
less than or equal to the maximum allowable V
CC
may be applied to
this pin when no voltage is applied to the V
CC
pins.
Interface Schematic
18
VGC
19
VCC2
Supply for the modulator stage only. A 10nF external bypass capacitor
is required and an additional 0.1
μ
F will be required if no other low fre-
quency bypass capacitors are nearby. The trace length between the pin
and the bypass capacitors should be minimized. The ground side of the
bypass capacitors should connect immediately to ground plane.
Same as pin 16.
20
21
GND1
Q SIG
Baseband input to the Q mixer. This pin is DC-coupled. The DC level of
1.3V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50k
minimum. A DC voltage less than or equal to
the maximum allowable V
CC
may be applied to this pin when no voltage
is applied to the V
CC
pins.
Reference voltage for the Q mixer. This voltage should be the same as
the DC voltage supplied to the Q SIG pin. For maximum carrier sup-
pression, DC voltage on this pin relative to the Q SIG DC voltage may
be adjusted. Input impedance of this pin is 50k
minimum. A DC volt-
age less than or equal to the maximum allowable V
CC
may be applied
to this pin when no voltage is applied to the V
CC
pins.
Reference voltage for the I mixer. This voltage should be the same as
the DC voltage supplied to the I SIG pin. For maximum carrier suppres-
sion, DC voltage on this pin relative to the I SIG DC voltage may be
adjusted. Input impedance of this pin is 50k
minimum. A DC voltage
less than or equal to the maximum allowable V
CC
may be applied to
this pin when no voltage is applied to the V
CC
pins.
Baseband input to the I mixer. This pin is DC coupled. The DC level of
1.3V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50k
minimum. A DC voltage less than or equal to
the maximum allowable V
CC
may be applied to this pin when no voltage
is applied to the V
CC
pins.
Not connected.
22
Q REF
See pin 21.
23
I REF
See pin 24.
24
I SIG
25
26
NC
VCO_ISET
An external resistor of 47k
is used to set the VCO current for mini-
mum phase noise.
Supply Voltage for the LO1 flip-flop and limiting amp only. This supply is
isolated to minimize the carrier leakage. A 1nF external bypass capaci-
tor is required, and an additional 0.1
μ
F will be required if no other low
frequency bypass capacitors are nearby. The trace length between the
pin and the bypass capacitors should be minimized. The ground side of
the bypass capacitors should connect immediately to ground plane.
External LO input to modulator. Controlled by VCO_EN signal. Logic
low is internal VCO, while logic high is external VCO.
27
VCC1
28
LO1-
See pin 29.
21 k
GC
40 k
BIAS
Q SIG
Q REF
I SIG
I REF
相關PDF資料 |
PDF描述 |
|---|---|
| RF2670 | 8MHZ DUAL BASEBAND AGC WITH PROGRAMMABLE LOW PASS FILTERING |
| RF2681 | W-CDMA LINEAR VARIABLE GAIN DRIVER AMPLIFIER |
| RF2689 | W-CDMA/GSM/DCS RECEIVE AGC AND DEMODULATOR |
| RF2861 | CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER |
| RF2861PCBA-410 | CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2668-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V 2PIN AMMO - Ammo Pack |
| RF2669-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V RESETTABLE 2PIN - Bag 制造商:TE Connectivity 功能描述:RXEF050S |
| RF266PC1 | 功能描述:RF MODULE 2.4GHZ CHIP RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:26X 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
| RF267 | 制造商:Thomas & Betts 功能描述:TERMINAL RING TONGUE #10 CRIMP YELLOW 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #10, CRIMP YELLOW 制造商:Thomas & Betts 功能描述:TERMINAL, RING TONGUE, #10, CRIMP YELLOW; Connector Type:Ring Tongue; Series:Sta-Kon; Insulator Color:Yellow; Termination Method:Crimp; Stud/Tab Size:#10; Wire Size AWG Max:4AWG; Contact Material:Copper; Contact Plating:Tin ;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Ring Tongue Terminal 4AWG 44.7mm 14.22mm Electro-Tin Bulk |
| RF2670 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:8MHZ DUAL BASEBAND AGC WITH PROGRAMMABLE LOW PASS FILTERING |
發布緊急采購，3分鐘左右您將得到回復。