- 您現在的位置：買賣IC網 > PDF目錄384884 > RF2667 (RF MICRO DEVICES INC) RECEIVE AGC AND DEMODULATOR PDF資料下載
參數資料
| 型號： | RF2667 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | RECEIVE AGC AND DEMODULATOR |
| 中文描述： | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO24 |
| 封裝： | PLASTIC, QSOP-24 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 129K |
| 代理商： | RF2667 |
7-4
RF2667
Rev A14 010622
7
Q
D
Pin
14
Function
IN SEL
Description
Selects between CDMA and FM mode. This is a digitally controlled
input. A logic “high” (
≥
VCC-0.7V
DC
) selects CDMA mode. A logic “l(fā)ow”
(<0.5V
DC
) selects FM mode. The impedance on this pin is 30k
.
Interface Schematic
15
Q OUT-
Balanced Baseband Output of Q Mixer. This pin is internally DC biased
and should be DC blocked externally. This output is active in both
CDMA and FM modes. The output can be used in a single-ended con-
figuration by leaving one of the two pins unconnected, however half the
output voltage will be lost. Each pin should be loaded with 2.5k
. The
balanced load should be 5k
. The single-ended output impedance is
1.2k
, while the balanced output impedance is 2.4k
.
16
17
18
Q OUT+
GND
FL-
Same as pin 15, except complementary output.
See pin 15.
Same as pin 6.
Balanced AGC Output/Demod Input. This balanced node is pinned out
to allow shunt filtering of the AGC output signal as it enters the demod-
ulator. The basic configuration of the filter should consist of a shunt
inductor and shunt capacitor, both connected to the power supply, as
the internal circuitry requires this power supply connection through the
inductor to operate.
19
20
21
FL+
GND
I OUT+
Same as pin 18, except complementary.
See pin 18.
Same as pin 6.
Balanced Baseband Output of I Mixer. This pin is internally DC biased
and should be DC blocked externally. This output is active in both
CDMA and FM modes. The output can be used in a single-ended con-
figuration by leaving one of the two pins unconnected, however half the
output voltage will be lost. Each pin should be loaded with 2.5k
. The
balanced load should be 5k
. The single-ended output impedance is
1.2k
, while the balanced output impedance is 2.4k
.
22
23
I OUT-
GC
Same as pin 21, except complementary output.
See pin 22.
Analog Gain Control for AGC Amplifiers. The valid control range is from
0.5 to 2.5V
DC
. These voltages are valid for ONLY a 37k
source
impedance. The gain range for the AGC is 95dB.
60 k
BIAS
IN SEL
60 k
1.2 k
1.2 k
V
CC
V
CC
Q OUT+
Q OUT-
1.2 k
1.2 k
V
CC2
V
CC2
FL+
FL-
V
CC1
V
CC1
1.2 k
1.2 k
V
CC
V
CC
I OUT+
I OUT-
21 k
BIAS
40 k
GC
相關PDF資料 |
PDF描述 |
|---|---|
| RF2668 | CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER WITH INTEGRATED PLL |
| RF2670 | 8MHZ DUAL BASEBAND AGC WITH PROGRAMMABLE LOW PASS FILTERING |
| RF2681 | W-CDMA LINEAR VARIABLE GAIN DRIVER AMPLIFIER |
| RF2689 | W-CDMA/GSM/DCS RECEIVE AGC AND DEMODULATOR |
| RF2861 | CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2667-000 | 制造商:TE Connectivity 功能描述:- Tape and Reel |
| RF2668 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER WITH INTEGRATED PLL |
| RF2668-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V 2PIN AMMO - Ammo Pack |
| RF2669-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V RESETTABLE 2PIN - Bag 制造商:TE Connectivity 功能描述:RXEF050S |
| RF266PC1 | 功能描述:RF MODULE 2.4GHZ CHIP RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:26X 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。