- 您現在的位置：買賣IC網 > PDF目錄384883 > RF2140 (RF MICRO DEVICES INC) 3V DCS POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2140 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 衰減器 |
| 英文描述： | 3V DCS POWER AMPLIFIER |
| 中文描述： | 1710 MHz - 1785 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封裝： | ULTRA SMALL, CERAMIC, MP16K01A, 16 PIN |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 176K |
| 代理商： | RF2140 |
2-134
RF2140
Rev A12 011031
2
P
required. In order to meet the GSM system specs
under those conditions, a PIN diode attenuator con-
nected to the input can be turned on. The figure below
shows how the attenuator and its controls are con-
nected.
T heory of Operation and Application Information
The RF2140 is a three-stage device with 28 dB gain at
full power. Therefore, the drive required to fully satu-
rate the output is +5dBm. Based upon HBT (Hetero-
junction
Bipolar
Transistor)
requires only a single positive 3V supply to operate to
full specification. Power control is provided through a
single pin interface, with a separate Power Down con-
trol pin. The final stage ground is achieved through the
large pad in the middle of the backside of the package.
First and second stage grounds are brought out
through separate ground pins for isolation from the out-
put. These grounds should be connected directly with
vias to the PCB ground plane, and not connected with
the output ground to form a so called “l(fā)ocal ground
plane” on the top layer of the PCB. The output is
brought out through the wide output pad, and forms the
RF output signal path.
technology,
the
part
The amplifier operates in near Class C bias mode. The
final stage is "deep AB", meaning the quiescent current
is very low. As the RF drive is increased, the final stage
self-biases, causing the bias point to shift up and, at
full power, draws about 1500mA. The optimum load for
the output stage is approximately 4.5
. This is the load
at the output collector, and is created by the series
inductance formed by the output bond wires, vias, and
microstrip, and 2 shunt capacitors external to the part.
The optimum load impedance at the RF Output pad is
4.5-j3.9
.
With this match, a 50
terminal impedance
is achieved. The input is internally matched to 50
with just a blocking capacitor needed. This data sheet
defines the configuration for GSM operation.
The input is DC coupled; thus, a blocking cap must be
inserted in series. Also, the first stage bias may be
adjusted by a resistive divider with high value resistors
on this pin to V
PC
and ground. For nominal operation,
however, no external adjustment is necessary as inter-
nal resistors set the bias point optimally.
When the device is driven at maximum input power self
biasing would occur. This results in less isolation than
one would expect, and the maximum output power
would be about -15dBm. If the drive power to the PA is
turned on before the GSM ramp-up, higher isolation is
The current through the PIN diode is controlled by two
signals: AT_EN and APC. The AT_EN signal allows
current through the PIN diode and is an on/off function.
The APC signal controls the amount of current through
the PIN diode. Normally, the AT_EN signal will be
derived from the VCO ENABLE signal available in
most GSM handset designs. If maximum isolation is
needed before the ramp-up, the AT_EN signal needs to
be turned on before the RF power is applied to the
device input. The current into this pin is not critical, and
can be reduced to a few hundred micro amps with an
external series resistor. Without the resistor, the pin will
draw about 700
μ
A.
Because of the inverting stage at the APC input, the
current through the PIN diode is inverted from the APC
voltage. Thus, when V
APC
is high for maximum output
power, the attenuator is turned off to obtain maximum
drive level for the first RF stage. When V
APC
is low for
maximum isolation, the attenuator is be turned on to
reduce the drive level and to avoid self-biasing.
The PIN diode is dimensioned such that a low V
APC
the
impedance of the diode is about 50 Ohm. Since the
input impedance of the first RF stage become very
high when the bias is turned off, this topology will main-
tain a good input impedance over the entire V
APC
con-
trol range.
VCC1 and VCC2 provide supply voltage to the first and
second stage, as well as provides some frequency
selectivity to tune to the operating band. Essentially,
5 k
750
500
2 k
RF IN
AT_EN
APC
VCC
From Bias
Stages
PIN
相關PDF資料 |
PDF描述 |
|---|---|
| RF2140PCBA | 3V DCS POWER AMPLIFIER |
| RF2145 | DCS1800/1900 POWER AMPLIFIER |
| RF2145PCBA | DCS1800/1900 POWER AMPLIFIER |
| RF2146 | PCS LINEAR POWER AMPLIFIER |
| RF2146PCBA | .1UF/630VDC METAL POLY CAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2140-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2140PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V DCS POWER AMPLIFIER |
| RF2141-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2142-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2144-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。