- 您現在的位置：買賣IC網 > PDF目錄384883 > RF2140 (RF MICRO DEVICES INC) 3V DCS POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2140 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 衰減器 |
| 英文描述： | 3V DCS POWER AMPLIFIER |
| 中文描述： | 1710 MHz - 1785 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封裝： | ULTRA SMALL, CERAMIC, MP16K01A, 16 PIN |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 176K |
| 代理商： | RF2140 |
2-132
RF2140
Rev A12 011031
2
P
SeeUpgradedProductRF2174
RF OUT
Same as pin 10.
2F0
Connection for the second harmonic trap. This pin is internally con-
nected to the RF OUT pins. The bonding wire together with an external
capacitor form a series resonator that should be tuned to the second
harmonic frequency in order to increase efficiency and reduce spurious
outputs.
VCC2
Same as pin 15.
Pin
1
Function
GND2
Description
Ground connection for the driver stage. Keep traces physically short
and connect immediately to the ground plane for best performance. It is
important for stability that this pin has it’s own vias to the groundplane,
to minimize any common inductance. This pin is internally connected to
the ground slug.
Control input for the PIN diode. The purpose of the PIN diode is to
attenuate the RF input drive level when the V
APC
is low. This serves
both to reduce the leakage through the device cause by self biasing
when driving with high level at the RF input, as well as to maintain a
good input match when the bias of the input stage is turned off. When
this pin is “high” the PIN diode control is turned on. See the Theory of
Operation for more details.
RF Input. This is a 50
input, but the actual impedance depends on the
interstage matching network connected to pin 5. An external DC block-
ing capacitor is required if this port is connected to a DC path to ground
or a DC voltage.
Interface Schematic
See pin 15.
2
AT_EN
3
RF IN
4
GND1
Ground connection for the pre-amplifier stage. Keep traces physically
short and connect immediately to the ground plane for best perfor-
mance. It is important for stability that this pin has it’s own vias to the
groundplane, to minimize any common inductance.
Power supply for the pre-amplifier stage and interstage matching. This
pin forms the shunt inductance needed for proper tuning of the inter-
stage match. Please refer to the application schematic for proper con-
figuration, and note that position and value of the components are
important.
Power Control for the driver stage and pre-amplifier. When this pin is
"low," all circuits are shut off. A "low" is typically 0.5V or less at room
temperature. A shunt bypass capacitor is required. During normal oper-
ation this pin is the power control. Control range varies from about 1.0V
for -10dBm to 2.6V for +33dBm RF output power. The maximum power
that can be achieved depends on the actual output matching; see the
application information for more details. The maximum current into this
pin is 5mA when V
APC1
=2.6V, and 0mA when V
APC
=0V.
See pin 3.
5
VCC1
See pin 3.
6
APC1
7
8
9
APC2
VCC
NC
Power Control for the output stage. See pin 6 for more details.
See pin 6.
Power supply for the bias circuits.
See pin 6.
Not connected. Connect this pin to the ground plane for compatibility
with future packages.
RF Output and power supply for the output stage. Bias voltage for the
final stage is provided through this wide output pin. An external match-
ing network is required to provide the optimum load impedance.
10
RF OUT
11
12
13
RF OUT
Same as pin 10.
Same as pin 10.
Same as pin 10.
Same as pin 10.
14
GND1
To PIN
diode
2 k
AT_EN
RF IN
GND 1
VCC1
From Bias
Stages
PIN
From Attn
control circuit
GND
VCC
To RF
Stages
GND
APC
GND
PCKG BASE
RF OUT
From Bias
Stages
相關PDF資料 |
PDF描述 |
|---|---|
| RF2140PCBA | 3V DCS POWER AMPLIFIER |
| RF2145 | DCS1800/1900 POWER AMPLIFIER |
| RF2145PCBA | DCS1800/1900 POWER AMPLIFIER |
| RF2146 | PCS LINEAR POWER AMPLIFIER |
| RF2146PCBA | .1UF/630VDC METAL POLY CAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2140-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2140PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V DCS POWER AMPLIFIER |
| RF2141-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2142-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2144-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。