- 您現在的位置：買賣IC網 > PDF目錄384875 > R2043T-E2 (RICOH COMPANY LTD) 4-wire Serial Interface PDF資料下載
參數資料
| 型號： | R2043T-E2 |
| 廠商： | RICOH COMPANY LTD |
| 元件分類： | XO, clock |
| 英文描述： | 4-wire Serial Interface |
| 中文描述： | REAL TIME CLOCK, PDSO10 |
| 封裝： | 4 X 2.9 MM, 1 MM HEIGHT, TSSOP-10 |
| 文件頁數： | 9/48頁 |
| 文件大?。?/td> | 458K |
| 代理商： | R2043T-E2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
R2043K/T
Q
GENERAL DESCRIPTION
O
Interface with CPU
The R2043K/T is connected to the CPU by four signal lines CE (Chip Enable), SCLK (Serial Clock), SI (Serial
Input), and SO (Serial Output), through which it reads and writes data from and to the CPU. The CPU can be
accessed when the CE pin is held high. Access clock pulses have a maximum frequency of 1 MHz allowing
high-speed data transfer to the CPU.
O
Clock and Calendar Function
The R2043K/T reads and writes time data from and to the CPU in units ranging from seconds to the last two
digits of the calendar year. The calendar year will automatically be identified as a leap year when its last two
digits are a multiple of 4. Consequently, leap years up to the year 2099 can automatically be identified as such.
*) The year 2000 is a leap year while the year 2100 is not a leap year.
O
Alarm Function
The R2043K/T incorporates the alarm interrupt circuit configured to generate interrupt signals to the CPU at
preset times. The alarm interrupt circuit allows two types of alarm settings specified by the Alarm_W registers
and the Alarm_D registers. The Alarm_W registers allow week, hour, and minute alarm settings including
combinations of multiple day-of-week settings such as "Monday, Wednesday, and Friday" and "Saturday and
Sunday". The Alarm_D registers allow hour and minute alarm settings. The Alarm_W outputs from /INTR pin, and
the Alarm_D outputs also from /INTR pin. Each alarm function can be checked from the CPU by using a polling
function.
O
High-precision Oscillation Adjustment Function
The R2043K/T has built-in oscillation stabilization capacitors (CG and CD), which can be connected to an
external crystal oscillator to configure an oscillation circuit. Two kinds of accuracy for this function are
alternatives. To correct deviations in the oscillator frequency of the crystal, the oscillation adjustment circuit is
configured to allow correction of a time count gain or loss (up to
±
1.5ppm or
±
0.5ppm at 25
°
C) from the CPU.
The maximum range is approximately
±
189ppm (or
±
63ppm) in increments of approximately 3ppm (or 1ppm).
Such oscillation frequency adjustment in each system has the following advantages:
* Allows timekeeping with much higher precision than conventional RTCs while using a crystal oscillator
with a wide range of precision variations.
* Corrects seasonal frequency deviations through seasonal oscillation adjustment.
* Allows timekeeping with higher precision particularly with a temperature sensing function out of RTC,
through oscillation adjustment in tune with temperature fluctuations.
O
Power-on Reset, Oscillation Halt Sensing Function and Supply Voltage Monitoring Function
The R2043K/T incorporates an oscillation halt sensing circuit equipped with internal registers configured to
record any past oscillation halt.
Power on reset function reset the control resisters when the system is powered on from 0V. At the same time, the
fact is memorized to the resister as a flag, thereby identifying whether they are powered on from 0V or battery
backed-up.
The R2043K/T also incorporates a supply voltage monitoring circuit equipped with internal registers configured to
record any drop in supply voltage below a certain threshold value. Supply voltage monitoring threshold settings
can be selected between 1.6V and 1.3V through internal register settings. The sampling rate is normally 1s.
The oscillation halt sensing circuit and the power-on reset flag are configured to confirm the established
invalidation of time data in contrast to the supply voltage monitoring circuit intended to confirm the potential
invalidation of time data. Further, the supply voltage monitoring circuit can be applied to battery supply voltage
monitoring.
O
Periodic Interrupt Function
The R2043K/T incorporates the periodic interrupt circuit configured to generate periodic interrupt signals aside
from interrupt signals generated by the alarm interrupt circuit for output from the /INTR pin. Periodic interrupt
signals have five selectable frequency settings of 2 Hz (once per 0.5 seconds), 1 Hz (once per 1 second), 1/60
Hz (once per 1 minute), 1/3600 Hz (once per 1 hour), and monthly (the first day of every month). Further,
periodic interrupt signals also have two selectable waveforms, a normal pulse form (with a frequency of 2 Hz or 1
Hz) and special form adapted to interruption from the CPU in the level mode (with second, minute, hour, and
month interrupts). The condition of periodic interrupt signals can be monitored with using a polling function.
O
32kHz Clock Output
The R2043K/T incorporates a 32-kHz clock circuit configured to generate clock pulses with the oscillation
12345
Rev.2.05 - 9 -
相關PDF資料 |
PDF描述 |
|---|---|
| R2043K | 4-wire Serial Interface |
| R2043K-E2 | 4-wire Serial Interface |
| R3111Q181B | LOW VOLTAGE DETECTOR |
| R3111Q191A | LOW VOLTAGE DETECTOR |
| R3111Q191B | LOW VOLTAGE DETECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R20440 | 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 400V 12A 2PIN DO-4 - Bulk |
| R2045D | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface Real Time Clock Module |
| R2045S | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface Real Time Clock Module |
| R20460 | 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 600V 12A 2PIN DO-4 - Bulk |
| R20480 | 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 800V 12A 2PIN DO-4 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。