- 您現在的位置：買賣IC網 > PDF目錄384875 > R2043K (Ricoh Co., Ltd.) 4-wire Serial Interface PDF資料下載
參數資料
| 型號： | R2043K |
| 廠商： | Ricoh Co., Ltd. |
| 英文描述： | 4-wire Serial Interface |
| 中文描述： | 4線串行接口 |
| 文件頁數： | 27/48頁 |
| 文件大?。?/td> | 458K |
| 代理商： | R2043K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
R2043K/T
12345
Rev.2.05 - 27 -
Q
Configuration of Oscillation Circuit and Correction of Time Count Deviations
O
Configuration of Oscillation Circuit
32kHz
CG
CD
A
OSCIN
OSCOUT
Oscillator
Circuit
The oscillation circuit is driven at a constant voltage of approximately 1.1v relative to the level of the VSS pin
input. As such, it is configured to generate an oscillating waveform with a peak-to-peak voltage on the order of
1.1v on the positive side of the VSS pin input.
< Considerations in Handling Crystal Oscillators >
Generally, crystal oscillators have basic characteristics including an equivalent series resistance (R1) indicating
the ease of their oscillation and a load capacitance (CL) indicating the degree of their center frequency.
Particularly, crystal oscillators intended for use in the R2043K/T are recommended to have a typical R1 value of
50k
and a typical CL value of 6 to 9pF. To confirm these recommended values, contact the manufacturers of
crystal oscillators intended for use in these particular models.
< Considerations in Installing Components around the Oscillation Circuit >
1)
Install the crystal oscillator in the closest possible vicinity to the real-time clock ICs.
2)
Avoid laying any signal lines or power lines in the vicinity of the oscillation circuit (particularly in the area
marked "A" in the above figure).
3)
Apply the highest possible insulation resistance between the OSCIN and OSCOUT pins and the printed
circuit board.
4)
Avoid using any long parallel lines to wire the OSCIN and OSCOUT pins.
5)
Take extreme care not to cause condensation, which leads to various problems such as oscillation halt.
< Other Relevant Considerations >
1)
For external input of 32.768-kHz clock pulses to the OSCIN pin:
DC coupling: Prohibited due to an input level mismatch.
AC coupling: Permissible except that the oscillation halt sensing circuit does not guarantee perfect
operation because it may cause sensing errors due to such factors as noise.
2)
To maintain stable characteristics of the crystal oscillator, avoid driving any other IC through 32.768-kHz
clock pulses output from the OSCOUT pin.
Typical externally-equipped element
X’tal : 32.768kHz
Standard values of internal elements
CG,CD 10pF typ
(R1=50k
typ)
(CL=6pF to 9pF)
相關PDF資料 |
PDF描述 |
|---|---|
| R2043K-E2 | 4-wire Serial Interface |
| R3111Q181B | LOW VOLTAGE DETECTOR |
| R3111Q191A | LOW VOLTAGE DETECTOR |
| R3111Q191B | LOW VOLTAGE DETECTOR |
| R3111Q191C | LOW VOLTAGE DETECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R2043K-E2 | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface |
| R2043T | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface |
| R2043T-E2 | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface |
| R20440 | 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 400V 12A 2PIN DO-4 - Bulk |
| R2045D | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface Real Time Clock Module |
發布緊急采購，3分鐘左右您將得到回復。