- 您現在的位置：買賣IC網 > PDF目錄98065 > PTH12040WAZ (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH12040WAZ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, DIP-20 |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 633K |
| 代理商： | PTH12040WAZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
DEVICE INFORMATION
Rset + 10 kW
0.8 V
V
O *
0.8 V
* 1.696 kW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
18
19
20
PTHXX040W
(Top View)
16
www.ti.com............................................................................................................................................... SLTS237G – DECEMBER 2004 – REVISED MARCH 2009
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
1, 3, 5, 10, 13,
The common ground connection for the VI and VO power connections. It is also the 0 Vdc reference for
GND
16
the control inputs.
VI
2, 4, 6
The positive input voltage power node to the module, which is referenced to common GND.
VO
9, 12, 15
The regulated positive power output with respect to the GND node.
The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a
lowlevel ground signal to this input disables the module’s output and turns off the output voltage. When
Inhibit(1)
7
the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit
pin is left open-circuit, the module produces an output whenever a valid input source is applied.
A 1%, 0.05-W resistor must be connected between this pin and GND to set the output voltage higher
than the minimum value. The set-point range for the output voltage is from 0.8 V to 5.5 V. The resistor
VO Adjust
17
required for a given output voltage may be calculated from the following formula. If left open circuit, the
module output defaults to its lowest output voltage value. For further information on the adjustment
and/or trimming of the output voltage, see the related Application Information section.
The specification table gives the preferred resistor values for a number of standard output voltages.
The sense inputs allow the regulation circuit to compensate for voltage drop between the module and
+Sense
11
the load. For optimal voltage accuracy, +Sense should be connected to VO. If it is left open, a low-value
internal resistor ensures that the output remains in regulation.
For optimal voltage accuracy, –Sense should be connected to the ground return at the load. If it is left
–Sense
14
open, a low-value internal resistor ensures that the output remains in regulation.
Connecting a resistor from this pin to signal ground allows the on threshold of the input undervoltage
lockout (UVLO) to be adjusted higher than the default value. The hysterisis can also be independenly
UVLO Prog
8
reduced by connecting a second resistor from this pin to VI. For further information, see the Application
Information section.
This is an analog control input that allows the output voltage to follow another voltage during power up
and power down sequences. The pin is active from 0 V, up to the nominal set-point voltage. Within this
range, the module output follows the voltage at the Track pin on a volt-for-volt basis. When the control
Track
18
voltage is raised above this range, the module regulates at its nominal output voltage. If unused, this
input should be connected to VI for a faster power up. For further information, see the Application
Information section.
When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input
Margin
20
requires an open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can
Down(1)
be accommodated with a series resistor. For further information, see the Application Information section.
When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open
Margin Up(1)
19
collector (open-drain) interface. It is not TTL compatible. The percent change can be reduced with a
series resistor. For further information, see the Application Information section.
(1)
Denotes negative logic: Open = Normal operation / Ground = Function active
Copyright 2004–2009, Texas Instruments Incorporated
5
Product Folder Link(s): PTH12040W
相關PDF資料 |
PDF描述 |
|---|---|
| PTN04050AAST | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAD | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAZT | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAZ | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAH | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12040WAZT | 功能描述:DC/DC轉換器 8.0-14Vin 5.5V 50A 2.045" x1.045"x0.357 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12045WAD | 制造商:Texas Instruments 功能描述: |
| PTH12045WAZ | 制造商:Texas Instruments 功能描述:- Rail/Tube |
| PTH12050 | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTH12050L | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:12 Vin |
發布緊急采購，3分鐘左右您將得到回復。