- 您現在的位置：買賣IC網 > PDF目錄98065 > PTH12040WAZ (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH12040WAZ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, DIP-20 |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 633K |
| 代理商： | PTH12040WAZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Prebias Startup Capability
UVLO
Threshold
V (5V/Div)
I
V
(1V/Div)
O
HORIZTAL SCALE:5ms/Div
StartupPeriod
HORIZTAL SCALE:10ms/Div
V 1(1V/Div)
O
V
(1V/Div)
O2
I 2(5 A/Div)
O
www.ti.com............................................................................................................................................... SLTS237G – DECEMBER 2004 – REVISED MARCH 2009
The capability to start up into an output prebias condition is available to all the 12-V input series of PTH/PTV
power modules. A prebias startup condition occurs as a result of an external voltage being present at the output
of a power module prior to its output becoming active. This often occurs in complex digital systems when current
from another power source is backfed through a dual-supply logic component, such as an FPGA or ASIC.
Another path might be via clamp diodes, sometimes used as part of a dual-supply power-up sequencing
arrangement. A prebias can cause problems with power modules that incorporate synchronous rectifiers. This is
because under most operating conditions, such modules can sink as well as source output current. The 12-V
input PTH modules all incorporate synchronous rectifiers, but do not sink current during startup, or whenever the
Inhibit pin is held low. Start up includes an initial delay (approximately 8–15 ms), followed by the rise of the
output voltage under the control of the module’s internal soft-start mechanism; see Figure 18.
Conditions for PreBias Holdoff
For the module to allow an output prebias voltage to exist (and not sink current), certain conditions must be
maintained. The module holds off a prebias voltage when the Inhibit pin is held low, and whenver the output is
allowed to rise under soft-start control. Power up under soft-start control occurs upon the removal of the ground
signal to the Inhibit pin (with input voltage applied), or when input power is applied with Auto-Track disabled[1]. To
further ensure that the regulator doesn’t sink output current, (even with a ground signal applied to its Inhibit), the
input voltage must always be greater than the applied prebias source. This condition must exist throughout the
power-up sequence.
The soft-start period is complete when the output begins rising above the prebias voltage. Once it is complete
the module functions as normal, and sinks current if a voltage higher than the nominal regulation value is applied
to its output.
Note: If a prebias condition is not present, the soft-start period is complete when the output voltage has risen
to either the set-point voltage, or the voltage applied at the module’s Track control pin, whichever is lowest.
Demonstration Circuit
Figure 19 shows the startup waveforms for the demonstration circuit shown in Figure 20. The initial rise in VO2 is
the prebias voltage, which is passed from the VCCIO to the VCORE voltage rail through the ASIC. Note that the
output current from the PTH12010L module (IO2) is negligible until its output voltage rises above the applied
pre-bias.
Figure 18. PTH12020W Startup
Figure 19. Pre-Bias Startup Waveforms
Copyright 2004–2009, Texas Instruments Incorporated
21
Product Folder Link(s): PTH12040W
相關PDF資料 |
PDF描述 |
|---|---|
| PTN04050AAST | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAD | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAZT | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAZ | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
| PTN04050AAH | 1 A SWITCHING REGULATOR, 310 kHz SWITCHING FREQ-MAX, PDMA5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12040WAZT | 功能描述:DC/DC轉換器 8.0-14Vin 5.5V 50A 2.045" x1.045"x0.357 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12045WAD | 制造商:Texas Instruments 功能描述: |
| PTH12045WAZ | 制造商:Texas Instruments 功能描述:- Rail/Tube |
| PTH12050 | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTH12050L | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:12 Vin |
發布緊急采購，3分鐘左右您將得到回復。