- 您現在的位置：買賣IC網 > PDF目錄66056 > PT6913A (TEXAS INSTRUMENTS INC) 1-OUTPUT 12 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PT6913A |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 12 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | HORIZONTAL THROUGH HOLE-23 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 130K |
| 代理商： | PT6913A |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
PT6900/6910 Series
Adjusting the Output Voltage of the PT6900/PT6910
Positive to Negative Converter Series
The negative output voltage of the Power Trends PT6900
Series ISRs may be adjusted higher or lower than the
factory trimmed pre-set voltage with the addition of a
single external resistor. Table 1 gives the allowable
adjustment range for each model in the series as Va (min)
and Va (max).
Adjust Up:
An increase in the output voltage is obtained
by adding a resistor R2, between pin 2 (Vo adjust) and
pin 8 (Remote Sense GND).
Adjust Down:
Add a resistor (R1), between pin 2 (Vo ad-
just) and pin 22 (Remote Sense Vo).
Refer to Figure 1 and Table 2 for both the placement and value
of the required resistor, either (R1) or R2 as appropriate.
Notes:
1. Only a single 1% resistor is required in either the (R1) or
R2 location. Do not use (R1) and R2 simultaneously.
Place the resistor as close to the ISR as possible.
2. Never connect capacitors from V
o adjust to either GND,
V
out, or the Sense pins. Any capacitance added to the
V
o adjust pin will affect the stability of the ISR.
3. If the sense pins are not being used, the resistors (R1) and
R2 can be connected to V
out and GND respectively.
4. An increase in the output voltage must be accompanied by
a corresponding reduction in the maximum output current.
The revised maximum output current must be reduced to
the equivalent of 12Watts.
i.e.
Iout (max)
=
12
Adc,
Va
where V
a is the adjusted output voltage.
Figure 1
The respective values of (R1) [adjust down], and R2 [ad-
just up], can also be calculated using the following formulas.
(R1)
=
24.9 (Va – Vr)
– Rs k
(Vo – Va)
R2
=
24.9 Vr
– Rs
k
(Va – Vo)
Where:
Vo = Original output voltage
Va = Adjusted output voltage
Vr = Reference voltage in Table 1
Rs = The resistance given in Table 1
Table1
PT6900/PT6910ADJUSTMENTRANGEANDFORMULAPARAMETERS
Series Pt #
5.0V Bus
PT6903/13
PT6901/11
PT6902/12
3.3V Bus
PT6904/14
PT6905/15
Vo (nom)
-1.5V
-2.0V
-5.2V
Va (min)
-1.2V
-1.4V
-2.7V
Va (max)
-3.4V
-4.5V
-6.5V
Vr
-1.0V
-0.92V
Rs (k
)
12.7
10.0
17.4
C
in
+
C
out
+
R2
(Up)
(R1)
(Down)
COM
Vout(-)
+Vin
PT6900/10
16 - 21
2
9 - 15
3 - 7
+Vin
-Vo
GND
Vo(adj)
Vo(sense)
22
8
GND(sense)
L
O
A
D
相關PDF資料 |
PDF描述 |
|---|---|
| PT6915N | 1-OUTPUT 12 W DC-DC REG PWR SUPPLY MODULE |
| PT6921A | SWITCHING REGULATOR, SMA23 |
| PT6921N | SWITCHING REGULATOR, SMA23 |
| PT6922C | SWITCHING REGULATOR, SMA23 |
| PT6921C | SWITCHING REGULATOR, SMA23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT6913C | 功能描述:DC/DC轉換器 -1.5Vout 9W 5V-Input Adj +to- Vltg Cnvtr RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT6913N | 功能描述:REG -1.5V 6A +5VIN ADJ VERT RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:PT6910 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最小）:36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT6914 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12 Watt 5V/3.3V Input Plus to Minus Voltage Converter SLTS113 |
| PT6914A | 功能描述:直流/直流開關轉換器 -2.0Vout 10W 3.3V-In Adj + to - Voltage RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PT6914C | 功能描述:DC/DC轉換器 -2.0Vout 10W 3.3V-In Adj + to - Voltage RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。