參數資料
型號： PSD211RM
廠商： 意法半導體
英文描述： Low Cost Field Programmable Microcontroller Peripherals
中文描述： 低成本現場可編程微控制器外圍設備
文件頁數： 20/51頁
文件大?。?/td> 348K
代理商： PSD211RM
PSD211R Famly
17
12.0
Control Signals
(Cont.)
12.1 ALE or AS
Connect the ALE or AS signal from your MCU to this pin where applicable, and program
the polarity using PSDsoft. The trailing edge (when the signal goes inactive) of ALE or AS
latches the address on the appropriate address pins.
12.2 WR or R/W
Your MCU should output a stand-alone write signal (WR) or a multiplexed read/write signal
(R/W). In either case, the signal should be connected to this pin.
12.3 RD/E
Your MCU should output either RD or E (clock). In either case, connect the appropriate
signal to this pin. Note: if you have an MCU that outputs DS, it will not be compatible with
the PSD211R, and you must use a PSD3XX family device.
12.4 PSEN
J
If your MCU does not output PSEN (or some program select enable equivalent signal),
tie this pin to Vcc (through a series resistor), and skip to the next signal.
J
If you use an 8-bit 8031 compatible MCU that outputs a separate signal when
accessing program space, such as PSEN, connect it to this pin. You would then use
PSDsoft to configure the EPROM in the PSD211R to respond to PSEN only or PSEN
and RD. If you have an 8031 compatible MCU, refer to the “Program/Data Space and
the 8031” section for further information.
12.5 A19/CSI
This pin is configured using PSDsoft to be either a chip select for the entire PSD device or
an additional PAD input. If your MCU can generate a chip-select signal, and you wish to
save power, use the PSD chip select feature. Otherwise, use this pin as an address or logic
input.
J
When configured as CSI (active-low PSD chip select): a low on this pin keeps the
PSD in normal operation. However, when a high is detected on the pin, the PSD
enters Power-down Mode. See Tables 7A and 7B for information on signal states
during Power-down Mode. See section 16 for details about the reduction of power
consumption.
J
When configured as A19, the pin can be used as an additional input to the PADs.
It can be used for address or logic. It can also be ALE/AS dependent or a transparent
input, which is determined by your PSDsoft design file. In A19 mode, the PSD is
always enabled.
Port
Configuration Mode(s)
State
AD0–AD15
All
MCU I/O
Latched Address Out
MCU I/O
Chip Select Outputs, CS0–CS7, CMOS
Chip Select Outputs, CS0–CS7, Open Drain
Address or Logic Inputs, A16-A18
Chip Select Outputs, CS8–CS10, CMOS only
Input (Hi-Z)
Unchanged
Logic 1
Unchanged
Logic 1
Hi-Z
Input (Hi-Z)
Logic 1
Port Pins PA0–PA7
Port Pins PB0–PB7
Port Pins PC0–PC2
Table 7A. Signal States During Power-down Mode
相關PDF資料
PDF描述
PSD211RN Low Cost Field Programmable Microcontroller Peripherals
PSD4235G2V-70UIT Flash In-System Programmable ISP Peripherals For 16-bit MCUs 3.3V Supply
PSD4235G2V-15U Flash In-System-Programmable Peripherals for 16-Bit MCUs
PSD4235G2V-15UI Tantalum Electrolytic Capacitor; Capacitance:33uF; Capacitance Tolerance:+/- 20 %; Working Voltage, DC:10V; Package/Case:3528-21; Terminal Type:PCB SMT; ESR:0.004ohm; Dielectric Material:Tantalum; Packaging:Cut Tape; Series:T520
PSD4235G2V-15UT Flash In-System Programmable ISP Peripherals For 16-bit MCUs 3.3V Supply
相關代理商/技術參數
參數描述
PSD211RN 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD2-120 制造商:Tamura Corporation of America 功能描述:
PSD2-16 制造商:Tamura Corporation of America 功能描述:
PSD2-20 制造商:Tamura Corporation of America 功能描述:
PSD2-24 制造商:Tamura Corporation of America 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*