參數資料
型號： PIC16F716-I/P
廠商： Microchip Technology
文件頁數： 74/136頁
文件大小： 0K
描述： IC PIC MCU FLASH 2KX14 18DIP
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 25
系列： PIC® 16F
核心處理器： PIC
芯體尺寸： 8-位
速度： 20MHz
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 13
程序存儲器容量： 3.5KB（2K x 14）
程序存儲器類型： 閃存
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
數據轉換器： A/D 4x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 18-DIP（0.300"，7.62mm）
包裝： 管件
產品目錄頁面： 639 (CN2011-ZH PDF)
配用： I3-DB16F716-ND - BOARD DAUGHTER ICEPIC3
AC162054-ND - HEADER INTERFACE ICD2 16F716
ACICE0202-ND - ADAPTER MPLABICE 18P 300 MIL
AC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16F716
DS41206B-page 40
2007 Microchip Technology Inc.
7.2
ADC Operation
7.2.1
STARTING A CONVERSION
To enable the ADC module, the ADON bit of the
ADCON0 register must be set to a ‘1’. Setting the GO/
DONE bit of the ADCON0 register to a ‘1’ will start the
Analog-to-Digital conversion.
7.2.2
COMPLETION OF A CONVERSION
When the conversion is complete, the ADC module will:
Clear the GO/DONE bit
Set the ADIF flag bit
Update the ADRES register with new conversion
result
7.2.3
TERMINATING A CONVERSION
If a conversion must be terminated before completion,
the GO/DONE bit can be cleared in software. The
ADRES register will not be updated with the partially
complete
Analog-to-Digital
conversion
sample.
Instead, the ADRES register will retain the value of the
previous conversion. Additionally, a 2 TAD delay is
required before another acquisition can be initiated.
Following this delay, an input acquisition is automati-
cally started on the selected channel.
7.2.4
ADC OPERATION DURING SLEEP
The ADC module can operate during Sleep. This
requires the ADC clock source to be set to the FRC
option. When the FRC clock source is selected, the
ADC waits one additional instruction before starting the
conversion. This allows the SLEEP instruction to be
executed, which can reduce system noise during the
conversion. If the ADC interrupt is enabled, the device
will wake-up from Sleep when the conversion
completes. If the ADC interrupt is disabled, the ADC
module is turned off after the conversion completes,
although the ADON bit remains set.
When the ADC clock source is something other than
FRC, a SLEEP instruction causes the present conver-
sion to be aborted and the ADC module is turned off,
although the ADON bit remains set.
7.2.5
SPECIAL EVENT TRIGGER
The ECCP Special Event Trigger allows periodic ADC
measurements without software intervention. When
this trigger occurs, the GO/DONE bit is set by hardware
and the Timer1 counter resets to zero.
Using the Special Event Trigger does not assure proper
ADC timing. It is the user’s responsibility to ensure that
the ADC timing requirements are met.
PWM Module” for more information.
7.2.6
A/D CONVERSION PROCEDURE
This is an example procedure for using the ADC to
perform an Analog-to-Digital conversion:
1.
Configure Port:
Disable pin output driver (See TRIS register)
Configure pin as analog
2.
Configure the ADC module:
Select ADC conversion clock
Configure voltage reference
Select ADC input channel
Select result format
Turn on ADC module
3.
Configure ADC interrupt (optional):
Clear ADC interrupt flag
Enable ADC interrupt
Enable peripheral interrupt
Enable global interrupt(1)
4.
Wait the required acquisition time(2).
5.
Start conversion by setting the GO/DONE bit.
6.
Wait for ADC conversion to complete by one of
the following:
Polling the GO/DONE bit
Waiting for the ADC interrupt (interrupts
enabled)
7.
Read ADC Result
8.
Clear the ADC interrupt flag (required if interrupt
is enabled).
Note:
The GO/DONE bit should not be set in the
same instruction that turns on the ADC.
Note:
A device Reset forces all registers to their
Reset state. Thus, the ADC module is
turned off and any pending conversion is
terminated.
Note 1: The global interrupt can be disabled if the
user is attempting to wake-up from Sleep
and resume in-line code execution.
2: See
相關PDF資料
PDF描述
PIC12C508A-04I/P IC MCU OTP 512X12 8DIP
PIC12F675-I/P IC MCU CMOS FLASH-BASE 8BIT 8DIP
PIC12F675-E/SN IC MCU CMOS 1K FLASH W/AD 8-SOIC
PIC16C765/JW IC MCU EPROM 8KX14 USB 40CDIP
PIC16LF1823-I/ML IC MCU 8BIT FLASH 16QFN
相關代理商/技術參數
參數描述
PIC16F716T-E/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F716T-E/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F716T-I/ML 制造商:Microchip Technology Inc 功能描述:MCU 8BIT RISC 28KB FLASH 2.5V/ - Tape and Reel
PIC16F716T-I/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F716T-I/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*