參數資料
型號： PIC16C558-04/P
廠商： Microchip Technology
文件頁數： 51/108頁
文件大?。?/td> 0K
描述： IC MCU OTP 2KX14 18DIP
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 25
系列： PIC® 16C
核心處理器： PIC
芯體尺寸： 8-位
速度： 4MHz
外圍設備： POR，WDT
輸入/輸出數： 13
程序存儲器容量： 3.5KB（2K x 14）
程序存儲器類型： OTP
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 18-DIP（0.300"，7.62mm）
包裝： 管件
產品目錄頁面： 636 (CN2011-ZH PDF)
配用： ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING
309-1059-ND - ADAPTER 18 ZIF BD W/18SO PLUGS
DVA16XP180-ND - ADAPTER DEVICE FOR MPLAB-ICE
AC164010-ND - MODULE SKT PROMATEII DIP/SOIC
2002 Microchip Technology Inc.
Preliminary
DS40143D-page 45
PIC16C55X
6.8
Power-Down Mode (SLEEP)
The Power-down mode is entered by executing a
SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the PD bit in the STATUS register is
cleared, the TO bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had,
before SLEEP was executed (driving high, low, or hi-
impedance).
For lowest current consumption in this mode, all I/O
pins should be either at V
DD, or VSS, with no external
circuitry drawing current from the I/O pin. I/O pins that
are hi-impedance inputs should be pulled high or low
externally to avoid switching currents caused by float-
ing inputs. The T0CKI input should also be at V
DD or
V
SS for lowest current consumption. The contribution
from on-chip pull-ups on PORTB should be considered.
The MCLR pin must be at a logic high level (V
IHMC).
6.8.1
WAKE-UP FROM SLEEP
The device can wake-up from SLEEP through one of
the following events:
1.
External RESET input on MCLR pin
2.
Watchdog Timer Wake-up (if WDT was enabled)
3.
Interrupt from RB0/INT pin or RB Port change
The first event will cause a device RESET. The two lat-
ter events are considered a continuation of program
execution. The TO and PD bits in the STATUS register
can be used to determine the cause of device RESET.
PD bit, which is set on power-up is cleared when
SLEEP is invoked. TO bit is cleared if WDT Wake-up
occurred.
When the SLEEP instruction is being executed, the
next instruction (PC + 1) is pre-fetched. For the device
to wake-up through an interrupt event, the correspond-
ing interrupt enable bit must be set (enabled). Wake-up
is regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address (0004h). In cases where the execution of
the instruction following SLEEP is not desirable, the
user should have an NOP after the SLEEP instruction.
The WDT is cleared when the device wakes-up from
SLEEP, regardless of the source of wake-up.
FIGURE 6-14:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
Note:
It should be noted that a RESET generated
by a WDT timeout does not drive MCLR
pin low.
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from SLEEP. The
SLEEP instruction is completely executed.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(4)
INT pin
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
Instruction
fetched
Instruction
executed
PC
PC+1
PC+2
Inst(PC) = SLEEP
Inst(PC - 1)
Inst(PC + 1)
SLEEP
Processor in
SLEEP
Interrupt Latency(2)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy cycle
PC + 2
0004h
0005h
Dummy cycle
T
OST(2)
PC+2
Note
1:
XT, HS or LP Oscillator mode assumed.
2:
T
OST = 1024TOSC (drawing not to scale). This delay will not be there for RC osc mode.
3:
GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line.
4:
CLKOUT is not available in these osc modes, but shown here for timing reference.
相關PDF資料
PDF描述
PIC16LF870-I/SO IC MCU FLASH 2KX14 EE A/D 28SOIC
06FMN-BMT-A-TF CONN FMN HSNG 6POS SNGL NOR SMD
PIC16LF88-I/SO IC MCU FLASH 4KX14 EEPROM 18SOIC
PIC18F26J53-I/SS IC PIC MCU 64KB FLASH 28SSOP
ATMEGA128L-8AI IC AVR MCU 128K 8MHZ LV 64-TQFP
相關代理商/技術參數
參數描述
PIC16C558-20/P 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C558-20/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C558 DIP18
PIC16C558-20/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C558-20/SO 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C558 SOIC18
PIC16C558-20/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*