參數資料
型號: PIC10F222-E/OT
廠商: Microchip Technology
文件頁數: 14/86頁
文件大?。?/td> 0K
描述: IC PIC MCU FLASH 512X12 SOT-23-6
標準包裝: 3,000
系列: PIC® 10F
核心處理器: PIC
芯體尺寸: 8-位
速度: 8MHz
外圍設備: POR,WDT
輸入/輸出數: 4
程序存儲器容量: 768B(512 x 12)
程序存儲器類型: 閃存
RAM 容量: 23 x 8
電壓 - 電源 (Vcc/Vdd): 2 V ~ 5.5 V
數據轉換器: A/D 2x8b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: SOT-23-6
包裝: 散裝
2007 Microchip Technology Inc.
DS41270E-page 19
PIC10F220/222
4.7
Program Counter
As a program instruction is executed, the Program
Counter (PC) will contain the address of the next
program instruction to be executed. The PC value is
increased by one every instruction cycle, unless an
instruction changes the PC.
For a GOTO instruction, bits 8:0 of the PC are provided
by the GOTO instruction word. The PC Latch (PCL) is
mapped to PC<7:0>.
For a CALL instruction or any instruction where the PCL
is the destination, bits 7:0 of the PC again are provided
by the instruction word. However, PC<8> does not
come from the instruction word, but is always cleared
Instructions where the PCL is the destination or Modify
PCL instructions, include MOVWF PC, ADDWF PC and
BSF PC
, 5.
FIGURE 4-5:
LOADING OF PC
BRANCH INSTRUCTIONS
4.7.1
EFFECTS OF RESET
The PC is set upon a Reset, which means that the PC
addresses the last location in program memory (i.e.,
the oscillator calibration instruction). After executing
MOVLW XX
, the PC will roll over to location 0000h and
begin executing user code.
4.8
Stack
The PIC10F220 device has a 2-deep, 8-bit wide
hardware PUSH/POP stack.
The PIC10F222 device has a 2-deep, 9-bit wide
hardware PUSH/POP stack.
A CALL instruction will PUSH the current value of stack
1 into stack 2 and then PUSH the current PC value,
incremented by one, into stack level 1. If more than two
sequential CALL’s are executed, only the most recent
two return addresses are stored.
A RETLW instruction will POP the contents of stack level
1 into the PC and then copy stack level 2 contents into
level 1. If more than two sequential RETLW’s are exe-
cuted, the stack will be filled with the address
previously stored in level 2.
Note:
Because PC<8> is cleared in the CALL
instruction or any Modify PCL instruction,
all subroutine calls or computed jumps are
limited to the first 256 locations of any
program memory page (512 words long).
PC
87
0
PCL
Instruction Word
GOTO
Instruction
CALL
or Modify PCL Instruction
PC
87
0
PCL
Instruction Word
Reset to ‘0’
Note 1: The W register will be loaded with the lit-
eral value specified in the instruction. This
is particularly useful for the implementa-
tion of data look-up tables within the
program memory.
2: There are no Status bits to indicate stack
overflows or stack underflow conditions.
3: There are no instructions mnemonics
called PUSH or POP. These are actions
that occur from the execution of the CALL
and RETLW instructions.
相關PDF資料
PDF描述
PIC10F222-I/P IC PIC MCU FLASH 512X12 8DIP
PIC10LF322T-I/OT MCU 8BIT 896B FLASH SOT23-6
PIC12C508-04I/SM IC MCU OTP 512X12 8-SOIJ
PIC12CE674/JW IC MCU EPROM 2KX14 A/D&EE 8CDIP
PIC12F1840-I/MF MCU 7KB FLASH 256B RAM 8-DFN
相關代理商/技術參數
參數描述
PIC10F222EP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers
PIC10F222I/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D
PIC10F222-I/MC 功能描述:8位微控制器 -MCU 0.75KB 23B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC10F222I/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D
PIC10F222-I/OT 功能描述:8位微控制器 -MCU 768B Flash 23B RAM 4 I/O 8bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT