- 您現在的位置：買賣IC網 > PDF目錄3896 > PIC10F206T-I/OT (Microchip Technology)IC PIC MCU FLASH 512X12 SOT23-6 PDF資料下載
參數資料
| 型號： | PIC10F206T-I/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 21/94頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 512X12 SOT23-6 |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 1 |
| 系列： | PIC® 10F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 3 |
| 程序存儲器容量： | 768B（512 x 12） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 24 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | SOT-23-6 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 637 (CN2011-ZH PDF) |
| 配用： | AC162059-ND - HEADER INTRFC MPLAB ICD2 8/14PIN XLT06SOT-ND - SOCKET TRAN ICE 6SOT W/CABLE AC163020-ND - ADAPTER PROGRAMMER PIC10F2XX AC164321-ND - MODULE SKT 6L PM3 SOT23 |
| 其它名稱： | PIC10F206T-I/OTDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
PIC10F200/202/204/206
DS41239D-page 26
2007 Microchip Technology Inc.
TABLE 5-2:
SUMMARY OF PORT REGISTERS
5.4
I/O Programming Considerations
5.4.1
BIDIRECTIONAL I/O PORTS
Some instructions operate internally as read followed
by write operations. The BCF and BSF instructions, for
example, read the entire port into the CPU, execute the
bit operation and rewrite the result. Caution must be
used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a BSF operation on bit 2 of GPIO will cause
all eight bits of GPIO to be read into the CPU, bit 2 to
be set and the GPIO value to be written to the output
latches. If another bit of GPIO is used as a bidirectional
I/O pin (say bit 0), and it is defined as an input at this
time, the input signal present on the pin itself would be
read into the CPU and rewritten to the data latch of this
particular pin, overwriting the previous content. As long
as the pin stays in the Input mode, no problem occurs.
However, if bit 0 is switched into Output mode later on,
the content of the data latch may now be unknown.
Example 5-1 shows the effect of two sequential
Read-Modify-Write instructions (e.g., BCF, BSF, etc.)
on an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired OR”, “wired
AND”). The resulting high output currents may damage
the chip.
EXAMPLE 5-1:
READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT
5.4.2
SUCCESSIVE OPERATIONS ON
I/O PORTS
The actual write to an I/O port happens at the end of an
instruction cycle, whereas for reading, the data must be
valid at the beginning of the instruction cycle (Figure 5-2).
Therefore, care must be exercised if a write followed by
a read operation is carried out on the same I/O port. The
sequence of instructions should allow the pin voltage to
stabilize (load dependent) before the next instruction
causes that file to be read into the CPU. Otherwise, the
previous state of that pin may be read into the CPU rather
than the new state. When in doubt, it is better to separate
these instructions with a NOP or another instruction not
accessing this I/O port.
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
Power-On
Reset
Value on
All Other Resets
N/A
TRISGPIO
—
I/O Control Register
---- 1111
N/A
OPTION
GPWU
GPPU
T0CS
T0SE
PSA
PS2
PS1
PS0
1111 1111
03h
STATUS
GPWUF
CWUF
—
TO
PD
Z
DC
C
00-1 1xxx
qq-q quuu(1), (2)
06h
GPIO
—
GP3
GP2
GP1
GP0
---- xxxx
---- uuuu
Legend:
Shaded cells are not used by PORT registers, read as ‘0’, – = unimplemented, read as ‘0’, x = unknown, u =
unchanged,
q
= depends on condition.
Note 1:
If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0.
2:
If Reset was due to wake-up on comparator change, then bit 6 = 1. All other Resets will cause bit 6 = 0.
;Initial GPIO Settings
;GPIO<3:2> Inputs
;GPIO<1:0> Outputs
;
GPIO latch
GPIO pins
;
----------
BCF
GPIO,
1 ;---- pp01
---- pp11
BCF
GPIO,
0 ;---- pp10
---- pp11
MOVLW 007h;
TRIS
GPIO
;---- pp10
---- pp11
;
Note 1:
The user may have expected the pin val-
ues to be ---- pp00. The 2nd BCF caused
GP1 to be latched as the pin value (High).
相關PDF資料 |
PDF描述 |
|---|---|
| 046238010010800+ | CONN FPC ONE-TOUCH LCK .5MM 10 |
| PIC10F202T-I/OT | IC PIC MCU FLASH 512X12 SOT23-6 |
| PIC10F204T-I/OT | IC PIC MCU FLASH 256X12 SOT23-6 |
| 006208510110000+ | CONN FFC/FPC 10POS 1MM ZIF SMD |
| 006200508130000 | CONN FFC/FPC 8POS 1MM R/A SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC10F220 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers |
| PIC10F220_1 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D |
| PIC10F220E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D |
| PIC10F220-E/MC | 功能描述:8位微控制器 -MCU 384B Flash16B RAM4 I/O8bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC10F220E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D |
發布緊急采購，3分鐘左右您將得到回復。