- 您現在的位置：買賣IC網 > PDF目錄11788 > PI7C8150BMAE (Pericom)IC PCI-PCI BRIDGE ASYNC 208-FQFP PDF資料下載
參數資料
| 型號： | PI7C8150BMAE |
| 廠商： | Pericom |
| 文件頁數： | 109/109頁 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 208-FQFP |
| 標準包裝： | 24 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 208-BFQFP |
| 供應商設備封裝： | 208-FQFP（28x28） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 1227 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 99 of 109
April 2009 – Revision 1.08
The instruction determines the test to be performed, the test data register to be accessed, or
both. The IR is two bits wide. When the IR is selected, the most significant bit is connected
to TDI, and the least significant bit is connected to TDO. The value presented on the TDI
pin is shifted into the IR on each rising edge of TCK. The TAP controller captures fixed
parallel data (1101 binary). When a new instruction is shifted in through TDI, the value
1101(binary) is always shifted out through TDO, least significant bit first. This helps
identify instructions in a long chain of serial data from several devices.
Upon activation of the TRST_L reset pin, the latched instruction asynchronously changes
to the id code instruction. When the TAP controller moves into the test state other than by
reset activation, the opcode changes as TDI shifts, and becomes active on the falling edge
of TCK.
16.2
BOUNDARY SCAN INSTRUCTION SET
The PI7C8150B supports three mandatory boundary-scan instructions (BYPASS,
SAMPLE and EXTEST). The table shown below lists the PI7C8150B’s boundary-scan
instruction codes.
Table 16-1. TAP Pins
Instruction
/
Requisite
Opcode (binary)
Description
EXTEST
IEEE 1149.1
Required
00000
EXTEST initiates testing of external circuitry, typically board-
level interconnects and off chip circuitry. EXTEST connects the
boundary-scan register between TDI and TDO. When EXTEST
is selected, all output signal pin values are driven by values
shifted into the boundary-scan register and may change only of
the falling edge of TCK. Also, when EXTEST is selected, all
system input pin states must be loaded into the boundary-scan
register on the rising-edge of TCK.
SAMPLE
IEEE 1149.1
Required
0001
SAMPLE performs two functions:
A snapshot of the sample instruction is captured on the
rising edge of TCK without interfering with normal
operation. The instruction causes boundary-scan register
cells associated with outputs to sample the value being
driven.
On the falling edge of TCK, the data held in the boundary-
scan cells is transferred to the slave register cells.
Typically, the slave latched data is applied to the system
outputs via the EXTEST instruction.
INTSCAN
00010
Enable internal SCAN test
CLAMP
00100
CLAMP instruction allows the state of the signals driven from
component pins to be determined from the boundary-scan
register while the bypass register is selected as the serial path
between TDI and TDO. The signal driven from the component
pins will not change while the CLAMP instruction is selected.
BYPASS
11111
BYPASS instruction selects the one-bit bypass register between
TDI and TDO pins. 0 (binary) is the only instruction that
accesses the bypass register. While this instruction is in effect,
all other test data registers have no effect on system operation.
Test data registers with both test and system functionality
performs their system functions when this instruction is selected.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26FD15PA | CONN PLUG 15POS STRAIGHT W/PINS |
| D38999/20MC8SN | CONN RCPT 8POS WALL MNT W/SCKT |
| D38999/20MD18SN | CONN RCPT 18POS WALL MNT W/SCKT |
| 0510210700 | CONN HOUSING 7POS 1.25MM |
| ADN8102ACPZ | IC EQUALIZER 4CH XSTREAM 64LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8150BMAI | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BMAI-33 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BMAIE | 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150BMAIE-33 | 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150BND | 功能描述:外圍驅動器與原件 - PCI 2-Port 32-Bit PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。