參數資料
型號： PDUSBD12PWDH
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： nullUSB interface device with parallel bus
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDSO28
文件頁數： 8/35頁
文件大?。?/td> 838K
代理商： PDUSBD12PWDH
Philips Semiconductors
PDIUSBD12
USB interface device with parallel bus
Product data
Rev. 08 — 20 December 2001
8 of 35
9397 750 09238
Koninklijke Philips Electronics N.V. 2001. All rights reserved.
operation before the data is sent to the host. The only exception is at the end of DMA
transfer, when the reception of pin EOT_N will stop DMA write operation and the
buffer content will be sent to the host on the next IN token.
For isochronous transfers, the local CPU and DMA controller have to guarantee that
they are able to sink or source the maximum packet size in one USB frame (1 ms).
The assertion of pin DMACK_N automatically selects the main endpoint (endpoint 2),
regardless of the current selected endpoint. The DMA operation of the PDIUSBD12
can be interleaved with normal I/O access to other endpoints.
DMA operation can be terminated by resetting the DMA enable register bit or the
assertion of EOT_N together with DMACK_N and either RD_N or WR_N.
The PDIUSBD12 supports DMA transfer in single address mode and it can also work
in dual address mode of the DMA controller. In the single address mode, DMA
transfer is done via the DREQ, DMACK_N, EOT_N, WR_N and RD_N control lines.
In the dual address mode, pins DMREQ, DMACK_N and EOT_N are
not
used;
instead CS_N, WR_N and RD_N control signals are used. The I/O mode Transfer
Protocol of PDIUSBD12 needs to be followed. The source of the DMAC is accessed
during the read cycle and the destination during the write cycle. Transfer needs to be
done in two separate bus cycles, storing the data temporarily in the DMAC.
8.
Endpoint description
The PDIUSBD12 endpoints are sufficiently generic to be used by various device
classes ranging from Imaging, Printer, Mass Storage and Communication device
classes. The PDIUSBD12 endpoints can be configured for 4 operating modes
depending on the Set mode command. The 4 modes are:
Mode 0
Mode 1
Mode 2
Mode 3
Non-isochronous transfer (Non-ISO mode)
Isochronous output only transfer (ISO-OUT mode)
Isochronous input only transfer (ISO-IN mode)
Isochronous input and output transfer (ISO-I/O mode).
相關PDF資料
PDF描述
PDIUSBD12D nullUSB interface device with parallel bus
PDIUSBD12PW nullUSB interface device with parallel bus
PDIUSBH11A Universal Serial Bus hub(通用串行總線集線器)
PDIUSBH11ANB Universal Serial Bus Hub
PDIUSBH11AD Universal Serial Bus Hub
相關代理商/技術參數
參數描述
PDUSBP11APWDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Transceiver
PDUSIDEBRKT 制造商:Tripp Lite 功能描述:RACK ENCLOSURE VERTICAL INSTALLATION KIT PDU, SURGE, POWER S - Bulk 制造商:Tripp Lite 功能描述:KIT PDU, SURGE, POWER STRIP 制造商:Tripp Lite 功能描述:Tripp Lite Rack Enclosure Vertical Installation Kit PDU, Surge, Power Strip
PDU-V101 功能描述:PHOTODIODE UV 0.31MM SQ TO-46 RoHS:否 類別:傳感器，轉換器 >> 光學 - 光電檢測器 - 光電二極管 系列:- 標準包裝:1 系列:- 波長:850nm 顏色 - 增強型:- 光譜范圍:400nm ~ 1100nm 二極管類型:引腳 nm 下響應率:0.62 A/W @ 850nm 響應時間:5ns 電壓 - (Vr)（最大）:50V 電流 - 暗（標準）:1nA 有效面積:1mm² 視角:150° 工作溫度:-40°C ~ 100°C 封裝/外殼:徑向，5mm 直徑（T 1 3/4） 其它名稱:475-2649-6
PDU-V101Q 功能描述:PHOTODIODE UV W/QW.31MM SQ TO-46 RoHS:否 類別:傳感器，轉換器 >> 光學 - 光電檢測器 - 光電二極管 系列:- 標準包裝:1 系列:- 波長:850nm 顏色 - 增強型:- 光譜范圍:400nm ~ 1100nm 二極管類型:引腳 nm 下響應率:0.62 A/W @ 850nm 響應時間:5ns 電壓 - (Vr)（最大）:50V 電流 - 暗（標準）:1nA 有效面積:1mm² 視角:150° 工作溫度:-40°C ~ 100°C 封裝/外殼:徑向，5mm 直徑（T 1 3/4） 其它名稱:475-2649-6
PDU-V102 功能描述:PHOTODIODE UV 0.87MM SQ TO-46 RoHS:否 類別:傳感器，轉換器 >> 光學 - 光電檢測器 - 光電二極管 系列:- 標準包裝:1 系列:- 波長:850nm 顏色 - 增強型:- 光譜范圍:400nm ~ 1100nm 二極管類型:引腳 nm 下響應率:0.62 A/W @ 850nm 響應時間:5ns 電壓 - (Vr)（最大）:50V 電流 - 暗（標準）:1nA 有效面積:1mm² 視角:150° 工作溫度:-40°C ~ 100°C 封裝/外殼:徑向，5mm 直徑（T 1 3/4） 其它名稱:475-2649-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*