參數資料
型號： PDIUSBH11ANB
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Universal Serial Bus Hub
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDIP32
封裝： PLASTIC, SOT-232-1, SDIP-32
文件頁數： 26/28頁
文件大小： 157K
代理商： PDIUSBH11ANB
Philips Semiconductors
Product specification
PDIUSBH11A
Universal Serial Bus Hub
1999 Jul 22
26
SOLDERING
Introduction
This text gives a very brief insight to a complex technology. A more
in-depth account of soldering ICs can be found in our “Data
Handbook IC26; Integrated Circuit Packages”(document order
number 9398 652 90011).
There is no soldering method that is ideal for all IC packages. Wave
soldering is often preferred when through-hole and surface mount
components are mixed on one printed circuit board. However, wave
soldering is not always suitable for surface mount ICs, or for
printed-circuit boards with high population densities. In these
situations, reflow soldering is often used.
Through-hole mount packages
S
OLDERING
BY
DIPPING
OR
BY
SOLDER
WAVE
The maximum permissible temperature of the solder is 260
°
C;
solder at this temperature must not be in contact with the joints for
more than 5 seconds. The total contact time of successive solder
waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the
temperature of the plastic body must not exceed the specified
maximum storage temperature (T
stg(max)
). If the printed-circuit board
has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
M
ANUAL
SOLDERING
Apply the soldering iron (24 V or less) to the lead(s) of the package,
either below the seating plane or not more than 2 mm above it. If the
temperature of the soldering iron bit is less than 300
°
C, it may
remain in contact for up to 10 seconds. If the bit temperature is
between 300 and 400
°
C, contact may be made for up to 5 seconds.
Surface mount packages
R
EFLOW
SOLDERING
Reflow soldering requires solder paste (a suspension of fine solder
particles, flux and binding agent) to be applied to the printed-circuit
board by screen printing, stencilling or pressure-syringe dispensing
before package placement.
Several methods exist for reflowing; for example, infrared/convection
heating in a conveyor-type oven. Throughput times (preheating,
soldering and cooling) vary between 100 and 200 seconds,
depending on heating method.
Typical reflow peak temperatures range from 215 250
°
C. The
top-surface temperature of the packages should preferably be kept
below 230
°
C.
W
AVE
SOLDERING
Conventional single-wave soldering is not recommended for surface
mount devices (SMDs) or printed-circuit boards with a high
component density, as solder bridging and non-wetting can present
major problems.
To overcome these problems, the double-wave soldering method
was specifically developed.
If wave soldering is used, the following conditions must be observed
for optimal results:
Use a double-wave soldering method comprising a turbulent wave
with high upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis
is
preferred
to be parallel to the transport direction of the
printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be
parallel to the transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream
end.
For packages with leads on four sides, the footprint must be
placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate solder thieves
downstream and at the side corners.
During placement, and before soldering, the package must be fixed
with a droplet of adhesive. The adhesive can be applied by screen
printing, pin transfer or syringe dispensing. The package can be
soldered after the adhesive has cured.
Typical dwell time is 4 seconds at 250
°
C. A mildly-activated flux will
eliminate the need for removal of corrosive residues in most
applications.
M
ANUAL
SOLDERING
Fix the component by first soldering two diagonally-opposite end
leads. Use a low-voltage (24 V or less) soldering iron applied to the
flat part of the lead. Contact time must be limited to 10 seconds at
up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one
operation within 2 to 5 seconds between 270 and 320
°
C.
相關PDF資料
PDF描述
PDIUSBH11AD Universal Serial Bus Hub
PDIUSBH11 Universal Serial Bus Hub
PDIUSBH11D Universal Serial Bus Hub
PDIUSBH11NB Plug In Relay Switch Function:4PDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Mounting Type:Socket; Contact Carrying Power:0.9W; Contact Rating:3A; Relay Type:General Purpose RoHS Compliant: Yes
PDIUSBH12 USB 2-port hub
相關代理商/技術參數
參數描述
PDIUSBH11D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Hub
PDIUSBH11DB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER
PDIUSBH11NB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Hub
PDIUSBH12 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*