參數資料
型號： PCF88331
廠商： NXP Semiconductors N.V.
英文描述： STN RGB - 132 X 132 X 3 driver
中文描述： 超扭曲的RGB - 132 × 132 × 3驅動程序
文件頁數： 16/112頁
文件大?。?/td> 469K
代理商： PCF88331
2003 Feb 14
16
Philips Semiconductors
Objective specification
STN RGB - 132
×
132
×
3 driver
PCF8833
6.2.5
B
OOSTER VOLTAGE ON
The LCD supply generation circuits will be switched on
when the Booster voltage on (BSTRON) command is sent.
The BSTRON command has a direct effect only when the
PCF8833 is not in Power-down mode (Sleep_OUT is not
active).
With a reset DISPON (see Section 6.2.18) and BSTRON
are set, the PCF8833 will start-up with Sleep_OUT (see
Section 6.2.7) following the built-in start-up sequence
which generates the requested voltages and switches on
the display, unless DISPOFF and/or BSTROFF was sent.
When the LCD supply generation circuits are switched on,
it is necessary to wait for a certain time before the power
circuitsbecomestable and thedisplay canbeswitchedon.
Because this time is dependent on the required V
LCD
voltage, the external components used, the applied supply
voltage and some other parameters, the PCF8833
monitors the LCD supply generation circuit internally and
will only switch-on the display when the LCD supply
generation circuits are stable.
The status of the LCD supply generation circuits can be
monitored with the read display status (RDDST)
command; see Section 6.2.7.
Figure 3 shows two sequences for using the BSTRON
command, assuming BSTROFF and DISPOFF were set
before sending Sleep_OUT. In sequence A the command
to switch the display on (DISPON) is sent to the PCF8833
before the BSTRON command is sent. Therefore the
display will only be switched on when the LCD supply
generation circuit generates a stable V
LCD
. In sequence B
the RDDST command is used to monitor the LCD supply
generation circuit and, after the D31 bit of the RDDST is
set to logic 1, the DISPON command will be sent;
see Section 6.2.7.
For the effect of possible combinations of commands
Sleep_IN/Sleep_OUT and BSTRON/BSTROFF; see
Table 17 and Fig.4. Figure 7 shows the effects of the
combination of commands BSTRON and BSTROFF with
DISPON and DISPOFF.
Table 7
Booster voltage on register bits
D/C
7
6
5
4
3
2
1
0
DEFAULT
0
0
0
0
0
0
0
1
1
03H
handbook, full pagewidth
MGU912
send Sleep_OUT 11H
monitor D[31]
RDDST 09H
start
end
send DISPON 29H
send BSTRON 03H
LCD will be switched on
when LCD supply
generation circuit
is stable
send Sleep_OUT 11H
start
end
send BISTRON 03H
send DISPON 29H
D31 = 1
D31 = 0
sequence A
sequence B
Fig.3 Booster voltage on flow charts.
相關PDF資料
PDF描述
PCF88332DA STN RGB - 132 X 132 X 3 driver
PCF8833U STN RGB - 132 X 132 X 3 driver
PCF8881 132 x 132 RGB single chip TFT driver with DC-to-DC converter
PCI-ADC MULTIFUNKTIONSKARTE 44 KANAL PCI BUS
PCI-DIO KARTE E/A 32 KANAL PCI BUS
相關代理商/技術參數
參數描述
PCF88332DA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8833U 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8833U/2DA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8881 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:132 x 132 RGB single chip TFT driver with DC-to-DC converter
PCF8881U/2DA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:132 x 132 RGB single chip TFT driver with DC-to-DC converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*