參數資料
型號： PCF2104L
廠商： NXP Semiconductors N.V.
英文描述： LCD controller/driver
中文描述： LCD控制器/驅動器
文件頁數： 24/56頁
文件大小： 366K
代理商： PCF2104L
1997 Dec 16
24
Philips Semiconductors
Product specification
LCD controller/driver
PCF2104x
11 INTERFACE TO MICROCONTROLLER
(I
2
C-BUS INTERFACE)
11.1
Characteristics of the I
2
C-bus
The I
2
C-bus is for bidirectional, two-line communication
between different ICs or modules. The two lines are a
serial data line (SDA) and a serial clock line (SCL).
Both lines must be connected to a positive supply via a
pull-up resistor. Data transfer may be initiated only when
the bus is not busy.
11.2
Bit transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable during the
HIGH period of the clock pulse as changes in the data line
at this time will be interpreted as a control signal.
11.3
Start and stop conditions
Both data and clock lines remain HIGH when the bus is not
busy. A HIGH-to-LOW transition of the data line, while the
clock is HIGH is defined as the START condition (S).
A LOW-to-HIGH transition of the data line while the clock
is HIGH is defined as the STOP condition (P).
11.4
System configuration
A device generating a message is a ‘transmitter’, a device
receiving a message is the ‘receiver’. The device that
controls the message is the ‘master’ and the devices which
are controlled by the master are the ‘slaves’.
11.5
Acknowledge
The number of data bytes transferred between the start
and stop conditions from transmitter to receiver is
unlimited. Each byte of eight bits is followed by an
acknowledge bit. The acknowledge bit is a HIGH level
signal put on the bus by the transmitter during which time
the master generates an extra acknowledge related clock
pulse. A slave receiver which is addressed must generate
an acknowledge after the reception of each byte. Also a
master receiver must generate an acknowledge after the
reception of each byte that has been clocked out of the
slave transmitter. The device that acknowledges must
pull-down the SDA line during the acknowledge clock
pulse, so that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse (set-up and
hold times must be taken into consideration). A master
receiver must signal an end of data to the transmitter by
not generating an acknowledge on the last byte that has
been clocked out of the slave. In this event the transmitter
must leave the data line HIGH to enable the master to
generate a stop condition.
11.6
I
2
C-bus protocol
Before any data is transmitted on the I
2
C-bus, the device
which should respond is addressed first. The addressing is
always carried out with the first byte transmitted after the
start procedure. The I
2
C-bus configuration for the different
PCF2104x READ and WRITE cycles is illustrated in
Figs 22, 23 and 24.
Fig.18 Bit transfer.
handbook, full pagewidth
MBC621
data line
stable;
data valid
change
of data
allowed
SDA
SCL
相關PDF資料
PDF描述
PCF2104LU LCD controller/driver
PCF2104N LCD controller/driver
PCF2104NU LCD controller/driver
PCF2105 LCD controller/driver
PCF2105MU LCD controller/driver
相關代理商/技術參數
參數描述
PCF2104LU 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver
PCF2104LU/12 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver
PCF2104LU/2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:LCD controller/driver
PCF2104LU/7 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:LCD controller/driver
PCF2104N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*